Tip: use quotes for an exact phrase, e.g. "teacher education"
Components and structures are designed based in their material’s mechanical properties such as Young's modulus or yield stress among others. Often those properties are obtained under monotonic mechanical tests but rarely under cyclic ones.…
Static traction tests on material samples for mechanical constructions have pointed out the loss of linearity of the specimen surface temperature with the applied load. This phenomenon is due to the heat generation caused by the local…
This paper focuses on the experimental investigation of the mechanical properties of the Alfas natural building stone. Two series of uniaxial compression tests and indirect tensile tests (Brazilian tests) were performed in order to…
This study investigates the effects of low concentration (0.1-0.4 wt.%) nano-boron carbide (B4C) reinforcement on the mechanical, thermal and fracture properties of epoxy nanocomposites. The nanocomposites were prepared via solution…
This study examines the changes in microstructure and mechanical properties of friction stir-welded (FSW) dissimilar joints between AA2014-T6 and AA5052-H32 aluminium alloys, with an emphasis on optimizing tool rotation speed for enhanced…
The analysis of the damaging micromechanisms in Ductile Cast Irons is often focused on ferritic matrix. Up to ten years ago, for this grades of DCIs, the main damaging micromechanism was identified with the graphite elements – ferritic…
Deep drawing of stainless steels thin sheets is a cold forming process used to produce components with complex geometries at limited costs. Although it seems a simple shaping technique, this technology requires a high level of know-how…
Crack tip stress-induced phase transformation mechanisms in nickel-titanium alloys (NiTi) were analyzed by Digital Image Correlation (DIC), under fatigue loads. In particular, Single Edge Crack (SEC) specimens, obtained from a commercial…
The aim of this work is a review of scientific results in the literature, related to the application of thermographic techniques to composite materials. Thermography is the analysis of the surface temperature of a body by infrared rays…
The damage development due to externally applied mechanical stress is a hot topic of interest involving several applications of everyday life, like civil engineering, monument restoration, construction evaluation and health monitoring.…
Abstract. In this article, the effect of nano-clay particles and heat-treating on thermo-mechanical fatigue (TMF) behaviors and failures of piston aluminum-silicon (AlSi) alloys was investigated. For this purpose, thermo-mechanical fatigue…
The quickly identify of fatigue limit of a mechanical component with good approximation is currently a significant practical problem not yet resolved in a satisfactory way. Generally, for a mechanical component, the fatigue strength…
This paper examines the influence of controlled heat treatments on the mechanical behaviour of Ti-6Al-4V (Grade 5 Titanium alloy) to improve its performance in structural and high performance applications. Ti-6Al-4V is widely used in…
Aluminium alloy composites are extensively utilised in the aerospace, automobile, and marine industries due to their lightweight structure and high strength-to-density ratio. However, there remains significant potential to further improve…
The aim of this study is to analyze the effect of different geometries and sections on the mechanical properties of epoxy specimens. Five tensile tests were carried out on three types of series. The experimental results obtained were…
Additive manufacturing research is continuously growing, and this field requires a full improvement of the capability and reliability of the processes involved. Of particular interest is the study of complex geometries production, such as…
This work investigated the effects of graphene and SiO2 addition on the mechanical and fracture properties of epoxy (80%) - Polylactic acid (PLA) (20 %) composites. Epoxy-PLA composites were loaded with graphene and SiO2 (0.1-0.5 wt. %…
In the current European standards for design of timber structures, the issue of timber-to-timber joint type is addressed only to squared timber, which makes the pinpointing of the round timber bolted joints load carrying capacity…
This study examines the influence of graphene nanoplatelets (GNPs) and multi-walled carbon nanotubes (MWCNTs) on the mechanical properties of SiO2-loaded epoxy-polylactic acid (PLA) composites. Epoxy and PLA were mixed to form the matrix…
Hot rolling normalization technology for producing sheets from a low-carbon steel, Steel S355J2, used in the Bulgarian Metallurgical Plant “STOMANA Industry SA” is under investigation. A newly introduced automatic application optimization…
Semi–empirical notch sensitivity factors q have been widely used to properly account for notch effects in fatigue design for a long time. However, the intrinsically empirical nature of this old concept can be avoided by modeling it using…
In this work two different titanium dental implants are analyzed in order to evaluate their mechanical strength. An ad-hoc designed experimental apparatus is prepared to test against fatigue these implants in a way that approximates as…
Basalt fabric composite, with different twill wave reinforcements, i.e. twill 2/2 and twill 1/3, have been studied in this work by means of experimental tests and numerical finite element (FE) simulations. As fabric reinforcements show…
In a series of applications, steel reinforced concrete structures are subjected to fatigue loads during their service life, what in most cases happens in corrosive environments. Surface treatments have been proved to represent proper…
Ultrasonic fatigue tests were carried out on stainless steel AISI 316 and 304, under two modalities: at room temperature and in immersion (water for 316 and antifreeze for 304 steels); all tests were carried out with a loading ratio R=-1.…
Fatigue tests and measurements of the volumetric distribution of metallurgical hydrogen in specimens cut from rolled I-beam 60Sh3 made of steel 10KhSND were carried out. Fatigue tests show a 20% reduction in fatigue limits compared to…
In this article, the characteristic curves of microindentation measured on Cu99 were analyzed on the basis of the analytical expression proposed by Habibi et al. (J. Mater. Res, 2021, 36 (15): 3074-3085). It was found that the ratio of the…
The objective of the present paper is to investigate the stress-controlled low-cycle fatigue behavior of piston aluminum-silicon (AlSi) alloy reinforced with nano-clay particles and T6 heat-treatment. The piston aluminum-silicon alloy…
The use of reinforcements in adhesive joints makes the stress distribution more uniform, improving their mechanical performance and adhesion. The present paper aims to verify the effectiveness and efficiency of the insertion of nylon 6…
In recent years, very-high-cycle fatigue (VHCF) behavior of metallic materials has become a major point of interest for researchers and industries. The needs of specific industrial fields (aerospace, mechanical and energy industry) for…
Ductile cast irons (DCIs) are characterized by a wide range of mechanical properties, mainly depending on microstructural factors, as matrix microstructure (characterized by phases volume fraction, grains size and grain distribution)…
The results of the investigation of both mechanical and acoustic emission (AE) behaviors of Mg4Li5Al alloy subjected to compression and tensile tests at room temperature are compared with the test results obtained using the same alloy and…
The paper presents a study of the application of Leak-Before- Break (LBB) concept in a relatively small-diameter high energy reactor coolant line, where it is proposed type AISI 316LN to be used as base material welded with type AISI 316L…
This report contains the results obtained from the mechanical characterization tests carried out on two different stainless steel (duplex 6%Ni, 22%Cr and super-austenitic 31%Ni, 28%Cr) used for the manufacturing of pipes which are employed…
The mechanical and nanomechanical properties of multi-walled carbon nanotube-reinforced polypropylene (MWCNT/PP) nanocomposite were investigated through tension tests (conducted on 2 wt% and 5 wt% specimens) and nanoindentation tests…
Conductive PLA is an innovative composite material that combines the ecological benefits of polylactic acid, a biodegradable thermoplastic, with electrical conductivity properties. Usually used in additive manufacturing for its ease of…
Considerable efforts have been made over the last decades to improve performance of spring steels, which would increase the service time of springs and also allow vehicles weight reduction. There are different possibilities of improving…
Stir casting technique has been used in the current study to process Al6061 reinforced with TiC particles of different concentrations. The processed compounds' composition of TiC and Al6061 has been verified by Energy Dispersive X-Ray…
This study aims to assess the delamination effect and predict the evolution of damage in 3D printed specimens to investigate the mechanical behavior occurring due to the delamination of the layers of 3D printed thermoplastic polymers.…
Al6061 and its composites are widely employed in applications requiring high strength and impact resistance. Heat treatment, particularly ageing, is a well-established method for enhancing the mechanical properties of these composites.…
The development of instrumented nanoindentation consists of non-destructive tests applied to miniature volumes of material (PMMA). The present research focuses on the factors explaining the variation in the trends of the mechanical…
The purpose of this study is to investigate the influence of hybrid nanoparticle reinforcement with Al2O3 and ZrO2 on the mechanical and wear parameters of Al6061 alloy-based Nano composites. MMC’s (Metal Matrix Composite) specimens were…
The post-curing process of cured composites is essential in enhancing the strength, stiffness, elevating the glass transition temperature, and reducing residual stress in polymer thermoset composites. The curing temperature and time are…
Presently, Functionally Graded Materials (FGMs) are extensively utilised in several industrial sectors, and the modelling of their mechanical behaviour is consistently advancing. Most studies investigate the impact of layers on the…
The use of composite materials allows to have a great flexibility in terms of mechanical and physical characteristics. One of the most used composite structure in naval field, is the sandwich, which is composed by a stacking sequence of…
Reinforced concrete has a weakness for corrosion which can cause the concrete to crack and the concrete structure to fail. To overcome this problem, a self-healing concrete method is needed that can close cracks and inhibit the rate of…
An experimental study was conducted to investigate the influence of operational defects, such as surface scratches and dents, on the residual mechanical properties of glass fiber-reinforced plastic (GFRP) during quasi-static tensile and…
Deep drawing of sheet metal is a crucial industrial process due to its high productivity and low cost per unit produced. Stainless steels are ideal for this process, given their high deformability compared to other steels. Despite its…
The paper details the studies carried out on a dual-size particulate composite prepared by stir casting using A 356 aluminum alloy and B4C powders. Three composite compositions, viz., A356 plus 2% B4C (44µm size and 105µm size in 1:1…
The paper investigates the use of 3D-printed components made from Polylactic Acid (PLA) for the restoration of architectural and ornamental elements, focusing on architectural/structural components. The material PLA was chosen for its…
