Tip: use quotes for an exact phrase, e.g. "teacher education"
The advances in the use of thermoelastic stress analysis (TSA) for fracture mechanics assessment are reviewed. The development of techniques to determine stress intensity factor is presented followed by the application of these techniques…
In this research, the effect of thermally expandable microcapsules (TEMs) on mode I fracture toughness of structural adhesives were investigated. The single-edge-notch bending (SENB) test was used. Firstly, a standard toughness test was…
Axial monotonic and load-controlled fatigue tests were performed to investigate the influence of forging at various temperatures and different deformation rates, on both the microstructural and mechanical behaviour of extruded AZ31B…
The effect of residual stresses on surface fatigue crack propagation and fracture mechanics parameters of intersecting orthogonal cracks is discussed. Mutual influence of intersecting cracks and biaxiality affects the nonsingular…
Models proposed to study the multiaxial fatigue damage phenomenon generally lack probabilistic interpretation due to their deterministic form. This implies failure compulsory happening at the plane exhibiting the maximum damage value…
The question about the existence of a correlation between the parameters C and m of the Paris’ law is re-examined in this paper. According to dimensional analysis and incomplete self-similarity concepts applied to the linear range of…
Magnesium (Mg) alloys are attractive as structural materials due to their light weight and high specific strength. It is well known that Mg alloy has hexagonal close-packed (HCP) structure and only basal slip or twinning can operate during…
The initiation and propagation of fatigue cracks during cyclic torsion loading was studied in a cast Al alloy (A357) with a relatively large (~500 ?m) grain size. 2D observations, revealed that multi site crack initiation occur on the…
This research addresses environmental concerns by exploring environmentally friendly composite materials as substitutes for non-biodegradable synthetic fibers. The study proposes the development of polymer matrix composites reinforced with…
Nodular cast iron (GJS) represents one of the most widely used materials for vehicle, energy and heavy machinery industry. Nevertheless, foundries struggling with the influence of local material defects in GJS like pores, shrinkages and…
The fatigue strength evaluation and fracture behavior for a dual phase steel-AA6061-T6 bonded joints with three different adhesives (DC-80, Betamate 120 and MP55420) are presented in this paper. Single lap shear tests were used to…
This paper presents an application of the boundary element method to the analysis of crack growth problems in linear elastic fracture mechanics and the correlation of results with experimental data. The methodology consists of computing…
This study has used the strain energy density (SED) approach to evaluate the stress intensity factor (SIF) of cracked cruciform welded joints in Hardox 450 steel. A microstructural analysis was made of Hardox 450 steel which is composed of…
Numerical investigations of the propagation of rolling contact fatigue crack filled by the liquid have been conducted. Two models of fluid – crack interaction have been considered. In the first model called “hydrostatic” the assumption of…
In the last years, a large amount of fatigue test results from plain and bluntly notched specimens made of AISI 304L stainless steel were synthetized in a single scatter band by adopting the specific heat loss per cycle (Q) as a damage…
This work is devoted to the comparative analysis of three techniques for measurement of energy dissipation in metals under fatigue crack propagation: original contact heat flux sensor, post-processing of the infrared thermography data and…
Experimental and numerical studies investigating fatigue crack growth were conducted on flat samples made of stainless steel AISE 304 and titanium alloy Grade 2. The heat flux from the crack tip caused by plastic deformation localization…
Fatigue takes a place more and more important in the design of structures, it remains a key point in the mechanical dimensioning of structures. The Friction Stir Welding (FSW) process is regarded today as the most promising alternative to…
Ultrasonic fatigue tests are carried out under the modality of three points bending on the granite stone. The testing specimens present a prismatic shape with the dimensions: 12 x 3 x 0.8 centimeters, in order to be supported at the two…
Limited by the mechanical properties of materials, silicon (Si) carbide insulated gate bipolar transistor (IGBT) can no longer meet the requirements of high power and high frequency electronic devices. Silicon carbide (SiC) IGBT…
The blade-disc dovetail interface in an aero-engine compressor is characterized by a non-uniform pressure distribution which can be obtained by an equivalent flat with round edge-on-plate configuration. The contact tractions for a mating…
The present work aims at developing a new approach towards the analysis of the crack path through the access to the information from the infrared (IR) video imaging of the steady fatigue crack growth. We first test some commonly available…
The dynamic behavior of beam-like structures with fatigue cracks forced by harmonic excitation is characterized by the appearance of sub and super-harmonics in the response even in presence of cracks with small depth. Since the amplitude…
TIG-dressing is a technique used to improve the fatigue strength of welded joints by a remelting of the weld toe region that promotes both a smoother transition between the plate and the weld crown and a residual stress redistribution.…
In this study, multiple and non-planar crack propagation analyses are performed using Fracture and Crack Propagation Analysis System (FCPAS). In an effort to apply and validate FCPAS procedures for multiple and non-planar crack propagation…
The crack growth behavior in 2324-T39 aluminium alloy was experimentally investigated. Two types of crack branching were observed. The mechanism of an uncommon crack branching which results from the link up of secondary crack with the main…
A three-parameters model for the interpolation of fatigue crack propagation data is proposed. It has been validated by a Literature data set obtained by testing 180 M(T) specimens under three different loading levels. In details, it is…
Blades of combustion turbines are extremely loaded turbojet elements, which transmit operative energy onto a rotor. Experiences of many years indicate, that cracks initiation and propagation in the blades during the operation time can…
In this work, the effects of natural particles on the micro failure mechanisms and static strength of an epoxy are studied using scanning electron microscope (SEM) technique. To this end, bulk specimens and adhesively bonded single lap…
Annular Linear Induction Pump (ALIP) is employed for low flow rate pumping of liquid metals because of its maintenance free operation. In order to monitor pump vibration during operation, a waveguide with accelerometer combination is…
Since fatigue cracking is caused in the middle-temperature conditions due to the stresses from heavy traffic and as the bitumen plays a very important role in controlling this failure, therefore, in recent years, the production of the…
Through this study, a numerical simulation based on 3D in order to investigate the effect of Crack-front shape on the stress intensity factor and fatigue crack growth behavior of center cracked aluminum plate repaired asymmetrically with a…
In several industrial applications, plastic, composites and ceramics replace a number of metallic structures such as copper, aluminum and steel. Most recently installed piping water and gas systems in the world are made of thermoplastic…
This paper aims to disclose the effects of weld size on hot spot stress in the calculation of fatigue performance of the joints. For this purpose, the author explored the hot spot stress of CHS-CFSHS T-joints, which consists of circular…
This study aims to investigate the delamination effect of a metal sandwich panel using a four-point bending simulation under continual spectrum loading. The most recent core designs of the sandwich panel have a cavity that can increase…
The objective of this work is to study the effects of contact parameters on the cracking parameters of a specimen and a pad assembly. These parameters have been studied and evaluated by the finite element method analysis in two dimensions…
Series of geometrically similar concrete beam of small, medium and large beam sizes has been tested under the action of monotonic and fatigue loading. Digital image correlation technique has been utilized to understand the fracture…
The paper describes the results of an experimental study of a polyurethane material treated by ion implantation technology. The problems of crack growth in the near-surface layer carbonized by ion treatment were investigated using digital…
The paper presents results of calculation for modelling of the stressstrain relationship in the case of block loads with mean load value. A model, based on the stable hysteresis loops, was assumed and modified to use for block loading…
