Tip: use quotes for an exact phrase, e.g. "teacher education"
Multiaxial fatigue behavior is an important topic in critical structural components. In the present study the biaxial-planar fatigue behavior of a powder metallurgical TRIP steel (Transformation Induced Plasticity) was studied by taking…
A novel cost-effective alternative in the form of nano/micro carbonized particles produced from waste bagasse fibers has been explored to modify the mechanical properties and fracture pattern of the resulting cementitious composites.…
This paper reports results of fatigue tests of friction stir welded (FSW) aluminium tubes. Relatively small 38 mm diameter tubes were used and hence an automated FSW process using a retracting tool was designed for this project, as the…
Nowadays, many components and structures are subjected to fatigue loading with a number of cycles higher than 107. In this scientific work, the behaviour of two kinds of tool steel was investigated in very high cycle fatigue regime. The…
This paper concerns the results of research into the influence of the composition of rock inclusions on the fracture response of cement-based composite specimens. Specially designed specimens of the nominal dimensions 40 × 40 × 160 mm with…
An inhomogeneous distribution of non-metallic inclusions can result from the steel casting process. The aim of the present study was to investigate the damaging effect of an inhomogeneous distribution of nonmetallic inclusions on the crack…
The article conducts a study on the iron tailings sand concrete's fracture behaviour based on the double-K criterion. Five sets of standard three-point bending beam specimens of concrete with 0%, 25%, 50%, 75% and 100% iron tailings sand…
Aeroengine manufacturers have to demonstrate that critical components such as turbine disks, made of DA Inconel 718, meet the certification requirements in term of fatigue crack growth. In order to be more representative of the in service…
In this paper, the attention is paid to investigation of the importance of the interfacial transition zone (ITZ) in selected fine-grained cement-based composites for the global fracture behaviour. This is a region of cement paste around…
In this study, the relationships between processing, structure and properties of self-reinforced ultra-high molecular weight polyethylene (UHMWPE) composites fabricated via thermal pressing are investigated. By systematically varying…
The mechanical and nanomechanical properties of multi-walled carbon nanotube-reinforced polypropylene (MWCNT/PP) nanocomposite were investigated through tension tests (conducted on 2 wt% and 5 wt% specimens) and nanoindentation tests…
The present investigation deals with the characterization of tensile behavior of various Fiber Reinforced Polymer composites under Thermo-Mechanical loading. Five different types of Uni-Directional (UD) composites of Carbon, Glass…
Development in material science impose to use different materials in production. This causes a problem for joining different materials because traditional joining techniques such as welding could not overcome this problem in industries…
This study investigates the physico-mechanical properties, mineralogical composition, deterioration processes, weathering patterns, and durability of building materials in the Ottoman Fort of Tamentfoust, Algiers, to inform heritage…
This work focuses on the synthesize of nanostructured (Fe65Co35)100-x (Pr6O11)x (x = 0, 5) powders using high energy ball milling. The influence of Pr6O11 on structural, morphological and magnetic properties of Fe65Co35 nanoparticles were…
The post-curing process of cured composites is essential in enhancing the strength, stiffness, elevating the glass transition temperature, and reducing residual stress in polymer thermoset composites. The curing temperature and time are…
This work investigated the effects of graphene and SiO2 addition on the mechanical and fracture properties of epoxy (80%) - Polylactic acid (PLA) (20 %) composites. Epoxy-PLA composites were loaded with graphene and SiO2 (0.1-0.5 wt. %…
Additive manufacturing (AM) technologies are currently contributing to significant progress in the design of lightweight metal components. Al alloys constitute the most studied light metal, particularly the Al-Si ones, due to their high…
Ultrasonic fatigue tests were carried out on stainless steel AISI 316 and 304, under two modalities: at room temperature and in immersion (water for 316 and antifreeze for 304 steels); all tests were carried out with a loading ratio R=-1.…
This paper examines the influence of controlled heat treatments on the mechanical behaviour of Ti-6Al-4V (Grade 5 Titanium alloy) to improve its performance in structural and high performance applications. Ti-6Al-4V is widely used in…
The purpose of this study is to investigate the influence of hybrid nanoparticle reinforcement with Al2O3 and ZrO2 on the mechanical and wear parameters of Al6061 alloy-based Nano composites. MMC’s (Metal Matrix Composite) specimens were…
A detailed investigation was conducted into the fracture mechanisms of cylindrical specimens made of a polycrystalline heat-resistant nickel-based alloy XH73MBTU-VD (EI698-VD), under uniaxial tension in the temperature range of 25–700°C.…
Diffusion welding is an advanced joining process that assures the feasibility of joining dissimilar metal alloys without producing metallurgical impurities at the joint interface. Two significant aerospace alloys, AA2219 and Ti-6Al-4V, are…
New biomedical supportive and lightweight structures require the creation of sustainable polymer composites of high strength and wear resistance. This research explores the use of alkali-treated pineapple leaf fiber (PALF) reinforced epoxy…
Abstract. In this article, the effect of nano-clay particles and heat-treating on thermo-mechanical fatigue (TMF) behaviors and failures of piston aluminum-silicon (AlSi) alloys was investigated. For this purpose, thermo-mechanical fatigue…
The present work focuses on the Tribological properties and corrosion behavior evaluation of sintered CoCrMo alloy. The CoCrMo alloy was elaborated by Powder metallurgy process at various sintering temperatures (1200°C, 1250°C and 1300°C).…
Interfacial interaction is investigated between the two basic constituents in carbon fiber reinforced plastics (CFRPs). Efforts have been made to quantify the interfacial shear strength (IFSS) between individual carbon fiber (CF) and epoxy…
This study presents an experimentally calibrated methodology to enhance the predictive accuracy of finite element simulations for Fused Deposition Modeling (FDM) parts in Abaqus by replacing idealized filament geometry with a physically…
This study examines the fracture toughness of Al6061 alloy-based hybrid composites reinforced with silicon carbide particles and cenosphere microspheres. Aluminum alloy Al6061 is widely utilized in structural applications due to its…
The goal of this work is to improve the understanding of the relation between the microstructural characteristics of Intercritical Austempered Ductile Cast Iron (IADI) and the damage micromechanisms observed during its tensile loading. The…
In recent times, the use of aluminum alloy-based Hybrid Metal Matrix Composites (HMMCs) is being increased in aerospace and automotive applications. HMMCs compensate for the low desirable properties of each filler used. However, the…
Our research described in this paper focused on fabricating and characterising polylactic acid (PLA) composites reinforced with randomly dispersed boron nitride nanoplatelets (BNNP). The integrated experimental analysis with the Finite…
The fatigue strength evaluation and fracture behavior for a dual phase steel-AA6061-T6 bonded joints with three different adhesives (DC-80, Betamate 120 and MP55420) are presented in this paper. Single lap shear tests were used to…
This study investigates jute fibre reinforced epoxy composites fabricated using a controlled vacuum bag moulding process, with emphasis on establishing reliable structure property relationships relevant to sustainable engineering…
The ambient and high-temperature fatigue crack growth behaviors in C(T) and SENT specimens of Ni-based superalloy for turbine disk application were studied in a wide interval of temperatures 25–750°C using a combination a electro- and…
This study investigates the effect of interleaving non-woven veils and their surface areal density on the curved beam strength (CBS) and interlaminar radial stress (ILRS) of glass/epoxy L-bend composite laminates. Carbon veils with areal…
Shape memory effect (SME) and the relation with corrosion behavior of Cu-Zn-Al Smart Memory Alloys (SMAs) were investigated using different techniques: Scanning Electron Microscopy equipped with an Energy Dispersive System, X-Ray…
This paper deals with the fatigue assessment of cast steel defects in terms of macroscopic shrinkage porosity. Within preliminary studies, a generalized Kitagawa diagram GKD was established by numerical analyses of V-notched specimens with…
A present study reveals the influence of nano Al2O3 and ZrO2 reinforcements on the fracture toughness of Hybrid Metal matrix Composites (HMMCs) made of Al6061 alloy. Composites are synthesized by varying weight fraction of alumina and…
This study examines the influence of graphene nanoplatelets (GNPs) and multi-walled carbon nanotubes (MWCNTs) on the mechanical properties of SiO2-loaded epoxy-polylactic acid (PLA) composites. Epoxy and PLA were mixed to form the matrix…
The widespread use of carbon fibre-reinforced polymer (CFRP) composites in sectors such as aerospace and aviation calls for the adoption of sustainable recycling protocols. This research evaluates the mechanical and tomographic…
In this study, in order to evaluate the effects of heavy vacuum slops (H.V.S) as rejuvenator and nano-Zycosil as an anti-stripping agent on used encapsulation method and mechanical performance of asphalt mixture samples, scanning electron…
