Tip: use quotes for an exact phrase, e.g. "teacher education"
In this paper, the macro and micro-mechanical fracture behavior was studied for aluminum (Al6061) alloy matrix, reinforced with various proportions of TiC particles such as 3wt%, 5wt% and 7wt%. The Al6061-TiC metal matrix composites were…
Chemical Vapour Infiltration (CVI) technique has been long used to produce carbon/carbon composites. The Pyrolytic Carbon (Py-C) matrix infiltrated by CVI could have different microstructures, i.e. Rough Laminar (RL), Smooth Laminar (SL)…
The analysis of the damaging micromechanisms in Ductile Cast Irons is often focused on ferritic matrix. Up to ten years ago, for this grades of DCIs, the main damaging micromechanism was identified with the graphite elements – ferritic…
This research addresses environmental concerns by exploring environmentally friendly composite materials as substitutes for non-biodegradable synthetic fibers. The study proposes the development of polymer matrix composites reinforced with…
Increased material demand in all sectors is primarily due to exponential growth in population to fulfill human needs and comforts. Recycling of collected aluminium beverage cans and Al 6061 alloy scraps from industries ensures energy…
Uniform dispersion of carbon nanotubes (CNTs) is a key issue for utilization of their reinforcement potential in CNT-reinforced metal matrix nanocomposites (MMNCs). It was reported that CNT clusters often exist in MMNCs prepared by various…
In this study, Al2O3 microparticle was used as a filler for pineapple fiber reinforced composites with different matrix polymers. The effect of Al2O3 microparticles in the epoxy and unsaturated polyester matrix on the mechanical, physical…
Duplex stainless steels are widely used in industry. This is due to their higher strength compared to austenitic steels and to their higher toughness than ferritic steels. They also have good weldability and high resistance to stress…
In the last decades, damaging micromechanisms in ductile cast irons (DCIs) have been widely investigated, considering both the matrix microstructure and the loading conditions influence. Considering the graphite nodules, they were…
Structural components made of fibre-reinforced materials are frequently used in engineering applications. Fibre-reinforced composites are multiphase materials, and complex mechanical phenomena take place at limit conditions but also during…
The major drawback observed in the ceramic particles reinforced aluminium matrix composites (AMCs) is the reduction of ductility. Incorporating fine metallic particles along with the ceramic reinforcements in the aluminium matrix tends to…
The damage evolution in a single domain aluminium/alumina freeze-cast composite has been examined using 3D X-ray computed tomography (CT). A single domain was extracted and loaded incrementally at an orientation of 45° to the lamellae…
A critical problem in the application of metal matrix composites is the presence of high residual thermal stresses induced during the development process. These thermally induced stresses are generally detrimental to the service life of…
The composite materials are normally made of reinforcements and resins. High-performance composites are generally termed hybrid composite materials. Generally, fiber-reinforced composite laminates are very weak in their out-of-plane…
Hybrid metal matrix composites (MMCs), recognized for their superior strength-to-weight ratios and synergistic property enhancements, are emerging as advanced materials capable of mitigating the inherent limitations observed in…
Due to the peculiar graphite elements shape, obtained by means of a chemical composition control (mainly small addition of elements like Mg, Ca or Ce), Ductile Cast Irons (DCIs) are able to offer the good castability of gray irons with the…
Ductile cast irons (DCIs) are characterized by a wide range of mechanical properties, mainly depending on microstructural factors, as matrix microstructure (characterized by phases volume fraction, grains size and grain distribution)…
In this paper the effect of reinforcement crack position and loading conditions (in mode I) on the stress intensity factors of the Al/SiCp metal matrix composite was examined using a finite element method. A simple cubic cell model with…
The stress state of the elastic fixed semi-strip with the regarding of the singularities at its edge is investigated in the article. The initial boundary problem is reduced to a vector boundary problem in the transformation’s domain by the…
The objective of this research work is to study the fracture behavior of Al6061 with graphite particulate composite produced by the stir casting technique. For the study different composition of the particulate metal matrix composite used…
The current work aims to investigate the mechanical properties of rare oxide reinforced Mg alloy based MMCs. Magnesium matrix considered in the study is AZ91D alloy, whereas rare earth oxides reinforced were CeO2 and Y2O3. The Y2O3…
The paper studies the processes of deformation and fracture in nanocomposites. The study was curry out by the method of mathematical modeling. The behavior of the nanosystem was described by the molecular dynamics apparatus. A modified…
In order to research the effect of cracks in red clay on shear strength through dry-wet cycle test, the experimenters used imaging software and a mathematical model to determine fractal dimension and crack ratio of surface cracks in red…
There is a tremendous increase in the use of high strength and high performance self-consolidating cementitious composites due to their superior workability and mechanical strengths. Cement composites are quasi-brittle in nature and…
This work focuses on the mechanical characterization of the inorganic matrix used for Fiber-Reinforced Cementitious Matrix (FRCM) composites, nowadays widely used to retrofit existing reinforced concrete and masonry structures. While…
In the present work, the fracture toughness (KIC) of full-depth (FD) fiber-reinforced concrete (FRC) and layered functionally graded concrete (FGC) matrix cracked (MC) beams has been determined by the equivalent relationships of the…
Hybrid continuous fiber–reinforced composites produced by fused deposition modeling (FDM) offer a promising solution for lightweight load-bearing structures. However, their mechanical performance is strongly governed by internal…
In this work the finite element method (FEM) was used to analyze the mechanical behavior of the composite materials subjected to the mechanical loading. This behavior is studied in terms of stress intensity factor variation as a function…
Simulating the concrete fracture unlike other elastic and brittle materials quite different due to its quasibrittleness. The present research focussed on assess softening behavior by varying different fractions of aggregates and cement…
In recent times, the use of aluminum alloy-based Hybrid Metal Matrix Composites (HMMCs) is being increased in aerospace and automotive applications. HMMCs compensate for the low desirable properties of each filler used. However, the…
Bendable concrete is also defined as engineered cementitious composites because of its great ductility and tight fracture width limitation. ECC mixtures by adding additional Portland cement, silica sand and fly ash, fiber types…
A geometrically simplified plane elasticity problem of a finite small crack emanating from a thin interfacial zone surrounding the circular inclusion situated in the finite bounded domain is investigated. The crack is arbitrarily oriented…
The benefits of resins nano-enhanced on the impact response of sandwich composites made by fiber glass/epoxy skins and balsa wood core were studied. Afterwards, the influence of the core's discontinuity was analyzed in terms of impact…
The demanding material quality criteria in the automotive and aerospace industries have recently had an impact on the development of lightweight aluminium alloys. The choice and application of metal-matrix composites as structural…
Lately porous shape memory alloys (SMA) have attracted great interest as low weight materials characterized by high energy dissipation capability. In the present contribution a micromechanical study of porous SMA is proposed, introducing…
In this work, a micromechanical model is used in order to predict the failure surface of cement concrete subject to multi-axial compression. In the adopted model, the concrete material is schematised as a composite with the following…
The need for the fabrication of sustainable aluminium matrix composites (AMCs) is being sought after as practical alternatives to conventional metals and their alloys. This study was undertaken to investigate the effect of sustainable…
The focus of this research was to investigate the effects of carbon nanofiber (CNF) reinforcement on the mechanical performance, interfacial characteristics, and abrasive wear behavior of short glass fiber/polyphenylene sulfide (GF/PPS)…
Steel fiber reinforced concrete is potentially very promising material with unique properties, which currently is widely used in some applications, such as floors and concrete pavements. However, lack of robust and reliable models of fiber…
The current study focuses on the influence of varying levels of boron-carbide (B4C) particles on mechanical and tribological characteristics of Al7075 hybrid composites that are strengthened by fixed percentages of graphite (Gr) and…
The Al2O3-SiC reinforced Al7075 Metal Matrix Composite (MMCs) is fabricated through liquid metallurgical technique. Ceramic particulates were amalgamated into aluminium alloy to achieve improved mechanical properties and wear resistance.…
Aluminium alloy composites are extensively utilised in the aerospace, automobile, and marine industries due to their lightweight structure and high strength-to-density ratio. However, there remains significant potential to further improve…
Main aim of this work is to investigate the influences of the addition of cenosphere and specimen crack length on the fracture toughness of Al6061-SiC composites. The experimental analysis was carried out for 3, 6 and 9 wt% proportions of…
In the current investigation, efforts are being made to produce an Al2014-Al2O3p composite with variable particle size of 88 mm by liquid stir casting route. 9, 12 and 15 weight proportions of Al2O3p were added to the Al2014 base alloy. By…
In this article the plain elasticity problem for a semi-strip with a transverse crack is investigated in the different cases of the boundary conditions at the semi-strip’s end. Unlike many works dedicated to this subject, the fixed…
The aim of the present paper is to propose innovative approaches able to improve the capability of classical damage indicators in detecting the damage position in linear systems. In particular, starting from classical indicators based on…
Aluminum composites exhibit high resistance to wear and corrosion, possess high strength, offer durability and more such properties. In this study, Al7075, reinforced with nano size SiC - Gr was produced by a stir casting technique and its…
A new class of material characterized by mechanical properties close to the traditional low and medium carbon steel is the Ductile Cast Irons (DCIs). High castability and low production costs allow them to be used in many fields, ranging…
Advanced polymer matrix composites are gaining the market in their way due to their exceptional specific stiffness, specific strength, fatigue, and corrosion resistance in the field of Auto-Tech, Aero-Tech, Biotech, etc. However, the lack…
The paper considers a pro-bionic lattice shell (PBLS) for civil aviation structures and the problem of getting the parameters of a local low-velocity impact taking the value of residual strain by fiber optic sensors (FOS) installed in…
