Tip: use quotes for an exact phrase, e.g. "teacher education"
The flexural failure of plain concrete beam occurs along with development of flexural crack on beam. In this paper by using ABAQUS, mechanism failure of plain concrete beam under three steps have been simulated. The cracking moment has…
We analyse the problem of a simply supported steel beam subjected to uniformly distributed load, strengthened with a pre-stressed fibre-reinforced polymer (FRP) laminate. We assume that the laminate is first put into tension, then bonded…
Bolted joints are the most common solution for joining composite components in aerospace structures. Critical structures such as wing to fuselage joints, or flight control surface fittings use bolted joining techniques. Recent research…
To seismic design of timber beam, effect of near-fault ground motion on timber beam has numerically been investigated, with refer to small displacement theory. The simulated near-fault ground motion is applied on the fixed base of timber…
A simple beam model for the evaluation of tile debonding due to substrate shrinkage is presented. The tile-adhesive-substrate package is modeled as an Euler-Bernoulli beam laying on a two-layer elastic foundation. An effective discrete…
Analyses of longitudinal fracture behavior of inhomogeneous beams which have continuously varying sizes of the cross-section along the beam length are carried-out. Beams of a rectangular cross-section are studied. It is assumed that beams…
A 3D mixed beam finite element is presented, modeling the warping of the cross-sections as an independent kinematic field. The beam formulation is derived on the basis of the Hu-Washizu variational principle, expressed as function of four…
The direct identification of the cohesive law in pure mode I of Pinus pinaster is addressed. The approach couples the double cantilever beam (DCB) test with digital image correlation (DIC). Wooden beam specimens loaded in the…
This paper investigated the static and dynamic behaviors of isotropic cracked simply supported beam using finite element analysis (FEA), ANSYS software. Modal and harmonic vibration analysis of intact and damaged beam were performed in…
An analytical study of longitudinal fracture in two-dimensional functionally graded cantilever beam configurations is carried-out with taking into account the non-linear behavior of material. A longitudinal crack is located arbitrary along…
The paper presents an experimental investigation of the flexural behaviour of reinforced concrete (RC) beam elements strengthened externally with stainless steel wire mesh (SSWM). SSWM has the potential to be an alternative composite…
This paper presents a dynamic and critical buckling analysis of the presence of a crack of steel-polymer concrete composite beams modelled using a refined quasi 3D beam theory. The beam model is a hollow steel box section filled with a…
Under cyclic load, local fatigue damage will occur in the metal damper widely used in the shear wall. This will deteriorate the stiffness of damper and weaken the hysteresis behaviour. The present paper proposed a new and easy method to…
The paper provides an evaluation of the nonlinear dynamic response of a cantilever beam made of composite material subjected to low-velocity impacts. The structure is assumed to respond in a quasi-static manner and modelled by a continuous…
The near surface mounted (NSM) method of inserting fiber reinforced polymer (FRP) elements (rods or lamina) into notches has been shown to be a good way for restoring reinforced concrete (RC) elements. The knowledge about the use of…
This paper describes the use of models of fracture-plastic materials for reinforced concrete in numerical modelling of beams made from reinforced concrete. The purpose of the paper is to use of a model of concrete for modelling of a…
We analyse the problem of a simply supported beam, strengthened with a fibre-reinforced polymer (FRP) strip bonded to its intrados and subjected to bending couples applied to its end sections. A mechanical model is proposed, whereby the…
This paper aims to disclose the influence law of cracks on instantaneous and long-term deflections of reinforced beam. For this purpose, four concrete beams were created, pre-loaded to varied degrees of cracking, and reinforced with carbon…
The paper presents the results of experimental and theoretical investigations of the mechanisms of crack formation in reinforced concrete beams subjected to quasi-static bending. The boundary-value problem has been formulated in the…
Adopting novel sandwich structures with FRP (Fibre Reinforced Polymer) skins and a metallic lattice core, both of which have high specific strength and stiffness, is one way to achieve better mechanical performance while remaining…
Cracks in cover of reinforced and pre-stressed concrete structures significantly influence the ingress of deleterious species causing decrease in durability of these structures. The paper is focused on the effect of fracture process on two…
This paper presents new analytical model of asymmetric mixed-mode bending (MMB) specimen of adhesively bonded pultruded GFRP joints. An easily applicable relationship for the calculation of the strain energy release rate of the asymmetric…
The present experimental study includes testing thirteen reinforced concrete beams with openings at different locations to investigate the efficiency of strengthening such openings. Different strengthening techniques around the opening…
This study investigates the effect of interleaving non-woven veils and their surface areal density on the curved beam strength (CBS) and interlaminar radial stress (ILRS) of glass/epoxy L-bend composite laminates. Carbon veils with areal…
To reduce the depth of floor-beam structures and to save the cost of headed-shear studs, many types of shallow composite beam have been developed during the last few years. Among them, the shallow-hollow steel beam consists of web…
The paper focuses on the effects of shear deformation and shear forces on the mode II contribution to the energy release rate in delaminated beams. A critical review of the relevant literature is presented, starting from the end-notched…
Multiaxial fatigue behavior is an important topic in critical structural components. In the present study the biaxial-planar fatigue behavior of a powder metallurgical TRIP steel (Transformation Induced Plasticity) was studied by taking…
The dynamic experimental and numerical analysis of cracked beams has been studied with the aim of quantifying the influence of depth crack on the dynamic response of steel beams. Artificial Neural Method ANN has been used where a numerical…
The assessment of existing masonry towers under exceptional loads, such as earthquake loads, requires reliable, expedite and efficient methods of analysis. These approaches should take into account both the randomness that affects the…
Adhesive bonding has become more efficient in the last few decades due to the adhesives developments, granting higher strength and ductility. As a result, adhesives are being increasingly used in industries such as the automotive…
In rolling contact fatigue (RCF), cracks usually initiate from inclusions beneath the surface and propagate to the contact surface. In the present study, synchrotron radiation computed laminography (SRCL) imaging was performed to observe…
In this work, we study the propagation of elastic waves in elongated solids with an array of equallyspaced deep transverse cracks, focusing in particular on the determination of stop-bands. We consider solids with different types of…
In this study, the influences of crack parameters like crack location from the left end, crack height, number of cracks and the magnitude of mass and the velocity of the transit load on the vertical displacements of the cracked simply…
The subject matter of these notes refers to the Ultimate Strength Design of 2-D steel framed structures and in particular to the analysis of the deformation state at collapse. The idea is based on the consideration that, if the structure…
The objective of this work is to analyze the behavior beams functionally graded, simply supported, under different conditions such as bending, buckling, and vibration and this by use shear deformation theories a two-dimensional (2D) and…
The aim of this work is the study of the effect of the finishing of the edge of glass when it has a structural function. Experimental investigations carried out for glass specimens are presented. Various series of annealed glass beam were…
In the present work, the fracture toughness (KIC) of full-depth (FD) fiber-reinforced concrete (FRC) and layered functionally graded concrete (FGC) matrix cracked (MC) beams has been determined by the equivalent relationships of the…
The paper presents an experimental analysis of tracking the path of the cracks and crack growth in strengthened or repair reinforced concrete short corbels bonded by carbon fiber fabrics under static and dynamic loads. The reinforced short…
Beam-column joints which shoulders high-level and vertical shearing effect that maintains balance of beam and column end is the major component influencing the performance of the whole framework. Post earthquake investigation suggests that…
The possibility of obtaining band gap structures in chiral auxetic lattices is here considered and applied to the case of inertial locally resonant structures. These periodic materials are modelled as beam-lattices made up of a periodic…
An experimental study and a proposed theoretical solution are conducted in the present study to investigate the ductile/brittle failure mode of reinforced concrete beams strengthened with an external steel plate. The present experimental…
This article investigates the possibility of exploiting innovative polyvinyl alcohol fibers reinforced with carbon nanotubes (PVA-CNT fiber) as a strain sensor in cement mortars used in the restoration of Cultural Heritage Monuments. Two…
Early damage detection plays an essential role in the safe and satisfactory maintenance of structures. This work investigates techniques use only damaged structure responses. A Timoshenko beam was modeled in finite element method, and an…
In this article, an analytical study was done to predict the behavior of the beam vis-à-vis bending, buckling, and dynamic responses of isotropic homogeneous beams based on an elastic foundation. The material properties of the FG-beams…
The presented work introduces a numerical parametric study on the crack propagation direction under mixed-mode conditions (mode I + II). It is conducted for the geometry of an eccentric asymmetric fourpoint bending of a single edge notched…
The present study of Ti6Al4V alloy production via Electron Beam Melting (EBM) represents a cutting-edge research topic impacting different strategic engineering applications. This can be attributed to the widespread use of this alloy and…
In this work, Cohesive Zone Modelling (CZM) was used to simulate failure of T-peel bonded joints with 1.5mm thick adherends, respectively, bonded toghether with Loctite Multibond 330 adhesive. The fracture toughness and load-opening…
The article conducts a study on the iron tailings sand concrete's fracture behaviour based on the double-K criterion. Five sets of standard three-point bending beam specimens of concrete with 0%, 25%, 50%, 75% and 100% iron tailings sand…
We review the recent experimental clarification of the fracture path in Liquid Metal Embrittlement with austenitic and martensitic steels. Using state of the art characterization tools (Focused Ion Beam and Transmission Electron…
Residual stress significantly influences the mechanical performance, fatigue resistance, and structural reliability of titanium alloys used in engineering applications. This study investigates the residual stress distribution induced by…
