Tip: use quotes for an exact phrase, e.g. "teacher education"
The recently proposed multiaxial racetrack filter (MRF) is able to deal with general non-proportional multiaxial load histories. While only requiring a single user-defined scalar filter amplitude, the MRF is able to synchronously eliminate…
Residual stresses are often inevitably introduced into the material during the fabrication processes, such as welding, and are known to have significant effects on the subsequent fatigue crack growth behavior of welded structures. In this…
The Moment-Of-Inertia (MOI) method has been proposed by the authors to solve some of the shortcomings of convex-enclosure methods, when they are used to calculate path-equivalent ranges and mean components of complex non-proportional (NP)…
This paper initially investigates the accuracy of two methods, i.e., the Maximum Variance Method (MVM) and the Maximum Damage Method (MDM), in predicting the orientation of the crack initiation plane in three different metallic materials…
The Static Thermographic Method (STM) involves analyzing the thermal behavior of a specimen subjected to a quasi-static tensile test. The temperature trend, measured by an infrared camera, follows three phases where the first and second…
The paper proposes a parallel extension of the Direct Optimized Probability Computation Method. This method can be used as an alternative to Monte Carlo – based approaches for problems of structural reliability. It does not depend on any…
Monitoring the energy release during fatigue tests of common engineering materials has been shown to give relevant information on fatigue properties, reducing the testing time and material consumption. During a static tensile test, it is…
In this work, a review and mathematical analysis of phenomenological models of residual strength and residual stiffness of polymer composite materials under fatigue loading have been carried out. The methodology of the analysis is…
Prediction of cyclic life under low cycle fatigue - high cycle fatigue (LCF-HCF) interaction is of paramount importance in the context of structural integrity of components in the primary side of fast reactors where such damage under…
This paper presents numerical models of a 3D printed plastic joint applicable to the connection of wooden structures. The research presented provides a comparison of two alternative solutions for the geometry of the joint and results from…
Fatigue tests and measurements of the volumetric distribution of metallurgical hydrogen in specimens cut from rolled I-beam 60Sh3 made of steel 10KhSND were carried out. Fatigue tests show a 20% reduction in fatigue limits compared to…
In the present paper, the approach based on the strain energy density (SED) averaged over a structural volume is reformulated to estimate the lifetime of notched components subjected to variable amplitude (VA) uniaxial fatigue loading. The…
Some numerical studies of crack propagation are based on using constitutive models that account for damage evolution in the material. When a critical damage value has been reached in a material point, it is natural to assume that this…
A Multi-Site Damage (MSD) crack growth simulation is presented, carried out by means of Dual Boundary Element Method (DBEM), in a two-dimensional analysis of a cracked butt-joint made of aluminium 2024 T3. An equivalent crack length is…
Cracks at notches deserve special consideration in the design of steam turbine components. This work is addressed to investigate the crack initiation behavior a 10%Cr rotor steel with the help of notched specimens under service-type…
In the last years, a large amount of fatigue test results from plain and bluntly notched specimens made of AISI 304L stainless steel were synthetized in a single scatter band by adopting the specific heat loss per cycle (Q) as a damage…
A stereo microscope coupled to a 3-D Digital Image Correlation system is used to measure strain ranges on the cyclic plastic zone ahead of a fatigue crack-tip. First, a very refined speckle pattern is applied on the surface of a…
This study reports an experimental investigation on the applicability of the net cross-sectional resistance rules of Eurocode 3 for steel plates with different bolt-hole configurations and steel grades, when relatively small fatigue cracks…
Nowadays, an increasing number of oil and gas transmission pipes are constructed with high-strength low alloy steels (HSLA); however, many of these pipelines suffer from different types of hydrogen damages, such as hydrogen-induced…
The present paper is devoted to an experimental study on the fracture behaviour of natural stones, commonly used as elements for building cladding, under both monotonic and cyclic loading, with particular emphasis to white Carrara marble.…
The work is devoted to the experimental study of heat dissipation caused by plastic deformation and failure processes taking place in a titanium alloy Ti-4.2Al-1.6Mn. To investigate the spatial and time evolution of temperature, a set of…
A method for assessing the degradation of mechanical properties of neat polyetheretherketone and its laminated composite reinforced with unidirectional carbon fibers is proposed. It is based on the calculation of the maximum and minimum…
The paper presents results of calculation for modelling of the stressstrain relationship in the case of block loads with mean load value. A model, based on the stable hysteresis loops, was assumed and modified to use for block loading…
Conductive PLA is an innovative composite material that combines the ecological benefits of polylactic acid, a biodegradable thermoplastic, with electrical conductivity properties. Usually used in additive manufacturing for its ease of…
Over the last two decades, piezoelectric actuators have emerged as a promising solution for structural repair. In this work, initially the stress intensity factor (SIF) estimation using the finite element (FE) approach at crack tips in…
