Tip: use quotes for an exact phrase, e.g. "teacher education"
The crack growth behavior of the aluminum alloy 6061 T651 was investigated using cruciform specimens with a measurement area of 120 x 120 x 2 mm3 with two center crack configurations of the starting notch parallel to one of the loading…
The CJP model of crack tip stresses is a modified version of the Williams crack tip stress field which takes account of simplified stress distributions that arise from the presence of a zone of plastic deformation associated with the crack…
While it is well known that fatigue crack growth in metals that display confined slip, such as high strength aluminium alloys, develop crack paths that are responsive to the loading direction and the local microstructural orientation, it…
Crack closure concept has been widely used to explain different issues of fatigue crack propagation. However, different authors have questioned the relevance of crack closure and have proposed alternative concepts. The main objective here…
Aeroengine manufacturers have to demonstrate that critical components such as turbine disks, made of DA Inconel 718, meet the certification requirements in term of fatigue crack growth. In order to be more representative of the in service…
Additive layer manufacturing has recently gained a lot of interest due to the feasibility of producing metallic components directly from a computer-aided design file of the part. Selective laser melting, one of the main additive layer…
It is generally accepted that fatigue crack growth is retarded after an overload, which has been explained either by plasticity-induced crack closure or near-tip residual stress. However, any interpretation of overload effect is…
The understanding of shear-mode crack growth mechanisms and crack branching phenomena is of great interest for a variety of practical engineering situations. Despite this fact, relatively little research is available regarding these…
In the present paper, mathematical models are proposed in order to analyze the strength of pinloaded lugs with semi-elliptical crack and through-the-thickness crack. The crack growth investigation of considered crack configurations tackles…
Fully automatic fatigue crack growth simulation system is developed using S-version FEM (SFEM). This system is extended to fracture in heterogeneous material. In the heterogeneous material, crack tip stress field becomes mixed mode…
Fatigue design is of vital importance to avoid fatigue small crack growth in engineering structures. This study shows that the critical fatigue design stress can be defined below the usual endurance limit, considered in rules and codes.…
Axles and shafts are of prime importance concerning safety in the transportation industry and railway in particular. Design rules for axles and shafts are mainly based on endurance curves for the material used according to the established…
A three-dimensional crack propagation simulation is performed by the Dual Boundary Element Method (DBEM). The Stress Intensity Factors (SIFs) along the front of a semi elliptical crack, initiated from the external surface of a hollow axle…
The focus of manufacturing is more and more on innovative and application-oriented products considering lightweight construction. Hence, especially functional graded materials come to the fore. Due to the application-matched functional…
Fatigue surface crack growth and the in-plane and out-of-plane constraint effects are studied through experiments and computations for aluminium alloy D16T. Subjects for studies are cruciform specimens under different biaxial loading and…
The subject for studies is an aluminium cylindrical hollow specimen with external axial and part circumferential semi-elliptical surface crack undergoing fatigue loads. Both the optical microscope measurements and the crack opening…
The aim of this paper is to calculate how the surface crack front and the dimensionless compliance evolve in cracked cylindrical bars subjected to cyclic tension or bending with different initial crack geometries (crack depths and aspect…
The effects of large amounts of hydrogen on the fatigue crack growth properties of torsional prestrained ferritic–pearlitic low-carbon steel were investigated. Hydrogen-precharged specimens were produced by conducting cathodic charge to…
In this study, multiple and non-planar crack propagation analyses are performed using Fracture and Crack Propagation Analysis System (FCPAS). In an effort to apply and validate FCPAS procedures for multiple and non-planar crack propagation…
This paper discusses features of fatigue crack initiation and growth in aeronautical VT3-1 titanium alloy under pure torsion loading in gigacycle regime. Two materials: extruded and forged VT3-1 titanium alloys were studied. Torsion…
The paper deals with the Stress Intensity Factor assessment of cracks at the intersection of holes loaded by internal pressure. Triangular flaws are considered at the intersection of two holes inside a specific specimen. The research…
This study compares both uniaxial and multiaxial variable amplitude experimental crack growth data for naturally initiated fatigue cracks in tubular specimens of 2024-T3 aluminum alloy to predictions based on two state-of-the-art analysis…
A class of fatigue crack growth models based on elastic–plastic stress–strain histories at the crack tip region and local strain-life damage models have been proposed in literature. The fatigue crack growth is regarded as a process of…
Fatigue surface crack growth is studied through experiments and computations for aluminum alloys D16T and B95AT (analogue of 2024 and 7075 aluminum). Subjects for studies are cylindrical hollow specimens with external semi-elliptical…
The crack growth behavior in 2324-T39 aluminium alloy was experimentally investigated. Two types of crack branching were observed. The mechanism of an uncommon crack branching which results from the link up of secondary crack with the main…
Crack closure influences fatigue crack growth rate and must be included in the design of components. Plasticity induced crack closure is intimately linked with the crack tip plastic deformation, which becomes residual as the crack…
The fatigue crack propagation is one of the major problems and of the real concern in the evaluation of the structural integrity of components. This is due to the fact that once a fatigue crack has been detected it is also known its effect…
This work is aimed at reproducing numerically a campaign of experimental tests performed for the development of reinforced panels, typically found in aircraft fuselage. The bonded reinforcements can significantly reduce the rate of fatigue…
An inhomogeneous distribution of non-metallic inclusions can result from the steel casting process. The aim of the present study was to investigate the damaging effect of an inhomogeneous distribution of nonmetallic inclusions on the crack…
The concept of the average stress has been employed to propose the maximum average tangential stress (MATS) criterion for predicting the direction of fracture angle. This criterion states that a crack grows when the maximum average…
In the current work an experimental study of the crack tip opening displacement (CTOD) is performed to evaluate the ability of this parameter to characterise fatigue crack growth. A methodology is developed to measure and to analyse the…
Threshold condition and rate of fatigue crack growth in both short and long crack regime appear to be significantly affected by the degree of crack deflection. In the present paper, a theoretical model of a periodically-kinked crack is…
Crack trajectories under different loading conditions and material microstructural features play animportant role when the conditions of crack initiation and crack growth under fatigue loading have to beevaluated. Unavoidable…
The paper delivers a critical review of the research data on the crack initiation and crack growth patterns characteristic of the components of the spline-bolted joints between the propeller shaft and reducer shaft at An-24, An-26, and…
There is an ever increasing need for accurate understanding of the fatigue crack growth behaviour in major engineering materials and components. With the move towards more complex, probabilistic assessments, the traditional ‘safe’ or…
In order to study the growth mechanism of fatigue cracks in ultrafine grained copper, stress controlled fatigue tests of round-bar specimens with a small blind hole as a crack starter were conducted. The hole was drilled on the surface…
A series of fatigue experiments on thin-walled tubes under tension and torsion, the experimental results – crack path and crack growth life – are measured and compared. It is observed that the cracks follow a curvature from a tensile to a…
Steel fiber reinforced concrete is potentially very promising material with unique properties, which currently is widely used in some applications, such as floors and concrete pavements. However, lack of robust and reliable models of fiber…
This paper is devoted to the analysis of the load path effect on I+II+III mixed mode fatigue crack propagation in a 316L stainless steel. Experiments were conducted in mode I+II and in mode I+II+III. The same maximum, minimum and mean…
Multiaxial fatigue behavior is an important topic in critical structural components. In the present study the biaxial-planar fatigue behavior of a powder metallurgical TRIP steel (Transformation Induced Plasticity) was studied by taking…
In this paper, crack propagation in Advanced Gas-cooled Reactor (AGR) graphite bricks with ageing properties is studied using the eXtended Finite Element Method (X-FEM). A parametric study for crack propagation, including the influence of…
In this work it is proposed a methodology for the evaluation of plasticity-induced crack shielding from the analysis of the crack tip displacements fields measured by digital image correlation. This methodology is based on the evaluation…
In the cohesive framework, a stress-state dependent cohesive model, combined with an irreversible damage parameter has been used in simulation of fatigue crack growth initiation and continued growth. The model is implemented as interface…
This study aims to investigate fatigue growth behaviour in AA7075-T651 under non-proportional mixed mode I and II loads. Fatigue tests were performed under cyclic tension and torsion using a thin-walled tubular specimen with a key-hole…
The premature contact of crack surfaces attributable to the near-tip plastic deformations under cyclic loading, which is commonly referred to as plasticity induced crack closure (PICC), has long been focused as supposedly controlling…
A four-parameters model for interpolation of fatigue crack growth data is presented. It has been validated by means of both data produced by the Authors and data collected from Literature. The proposed model is an enhanced version of a…
Thin rimmed and webbed gears are used in particular applications to reduce systems weight. This kind of gears need an accurate and fail safe design. As a matter of fact, a possible failure, due to bending fatigue, consists in crack…
The paper contains plane strain analysis of uniformly stretched plate working in creep condition. The plate contains initial defects in forms of central and/or edge cracks working in mode I. These cracks are modelled by attributing…
The simulation of critical and subcritical crack propagation in heterogeneous materials is not a simple problem in computational mechanics. These topics can be studied with different theoretical tools. In the crack propagation problem it…
The aim of this research is to clarify the influence of vacuum carburizing on the fatigue-crack progress characteristics of DSG2 steel. The test specimen tempering material (QT material) and vacuum carburizing material (VC material) has…
