Tip: use quotes for an exact phrase, e.g. "teacher education"
Crack initiation characteristics and fatigue property of a high-strength steel in very-high-cycle fatigue (VHCF) regime under different stress ratios were investigated in this paper. Fatigue tests were performed at stress ratios of -1…
The paper deals with the Stress Intensity Factor assessment of cracks at the intersection of holes loaded by internal pressure. Triangular flaws are considered at the intersection of two holes inside a specific specimen. The research…
Titanium alloy (Ti-6Al-4V) having a bimodal “harmonic structure”, which consists of coarsegrained structure surrounded by a network structure of fine grains, was fabricated by mechanical milling (MM) and spark plasma sintering (SPS) to…
Despite the extensive studies on the effect of width-thickness ratio and residual stress on member behavior, few scholars have probed into the residual stress distribution on the I-section members. Based on the principle of blind hole…
This paper studies multiaxial low cycle fatigue crack mode and failure life of Ti-6Al-4V. Stress controlled fatigue tests were carried out using a hollow cylinder specimen under multiaxial loadings of ?=0, 0.4, 0.5 and 1 of which stress…
The objective of this work is to evaluate the effects of mean stress on the fatigue behavior of ASTM A743 CA6NM alloy steel. It is used in several hydrogenator turbine components. In order to achieve it, 33 specimens were experimentally…
Materials can be classified as shear or tensile sensitive, depending on the main fatigue microcrack initiation process under multiaxial loadings. The nature of the initiating microcrack can be evaluated from a stress scale factor (SSF)…
In order to study the growth mechanism of fatigue cracks in ultrafine grained copper, stress controlled fatigue tests of round-bar specimens with a small blind hole as a crack starter were conducted. The hole was drilled on the surface…
A new critical plane approach based on the modified Manson-Coffin curve method (MMCCM) is presented in this paper for predicting fatigue lifetime under variable amplitude (VA) multiaxial fatigue loading. The critical plane is assumed to…
The subject for studies is an aluminium cylindrical hollow specimen with external axial and part circumferential semi-elliptical surface crack undergoing fatigue loads. Both the optical microscope measurements and the crack opening…
The crack growth behavior of the aluminum alloy 6061 T651 was investigated using cruciform specimens with a measurement area of 120 x 120 x 2 mm3 with two center crack configurations of the starting notch parallel to one of the loading…
Fatigue life tests under constant and variable amplitude loadings were performed on the tube-tube thin-walled welded specimens made of magnesium (AZ31 and AZ61) alloys. The tests included pure axial, pure torsional and combined in-phase…
Affected by physical properties of various components, characteristics and stress states of junction surface and other multiple factors, concrete, as a kind of multi-phase composite material, has complicated failure mechanism, thus making…
The damage development due to externally applied mechanical stress is a hot topic of interest involving several applications of everyday life, like civil engineering, monument restoration, construction evaluation and health monitoring.…
The modified Carpinteri-Spagnoli (C-S) criterion is a multiaxial high-cycle fatigue criterion based on the critical plane approach. According to such a criterion, the orientation of the critical plane is linked to both the averaged…
Non-singular terms in the series expansion of the elastic crack-tip stress fields, commonly referred to as the T-stress. The T-stress is as an additional stress field characterizing parameter to stress intensity factor (K) in the analysis…
This paper presents the development of the multiple linear regression approach based on the stress ratio and applied load that was assessed using entropy generation. The energy dissipation is associated with material degradation to…
In this investigation, three-dimensional elastic finite element analyses have been conducted to compute the stress intensity factor (KI) in a SENB specimen with varied thickness (B) and crack-length to width ratio (a/W). The results…
The fictitious notch rounding concept is applied for the first time to V-notches with root hole subjected to in-plane mixed mode loading. Out-of-bisector crack propagation is taken into account. The fictitious notch radius is determined as…
In the literature, there are many criteria of multiaxial fatigue. They are based on various assumptions and parameters describing the process of fatigue. Among them, there is a special group of criteria based on the concept of critical…
Modified version of the crack compliance method is used for determination of stress intensity factor (SIF) related to narrow notches emanating from cold-expanded holes. These notches are inserted at different stages of low-cycle fatigue…
In the present paper, the multiaxial fatigue life assessment of notched structural components is performed by employing a strain-based multiaxial fatigue criterion. Such a criterion, depending on the critical plane concept, is extended by…
The fatigue behaviour of concrete has become more important for the design of constructions due to the desire to build slimmer structures, which are more sensitive to fatigue loading. This article aims to evaluate and compare the fatigue…
Fatigue surface crack growth and the in-plane and out-of-plane constraint effects are studied through experiments and computations for aluminium alloy D16T. Subjects for studies are cruciform specimens under different biaxial loading and…
Closure-free long cracks under the remote mode III loading grow in a more complicated way than those under the remote mode II. For bcc metals, a coplanar in-plane spreading of tongues driven by the local mode II loading components at…
The influence of fiber orientation on the crack propagation behavior was studied with single edgenotched specimens which were cut from an injection-molded plate of short-fiber reinforced plastics of polyphenylenesulphide (PPS) reinforced…
The aim of this paper is to calculate how the surface crack front and the dimensionless compliance evolve in cracked cylindrical bars subjected to cyclic tension or bending with different initial crack geometries (crack depths and aspect…
Multiaxial fatigue behavior is an important topic in critical structural components. In the present study the biaxial-planar fatigue behavior of a powder metallurgical TRIP steel (Transformation Induced Plasticity) was studied by taking…
Crack closure concept has been widely used to explain different issues of fatigue crack propagation. However, different authors have questioned the relevance of crack closure and have proposed alternative concepts. The main objective here…
On the mode O existence in three-dimensional plates weakened by circular and elliptical holes under mode II loading It is known for long time that in a cracked plate subjected to anti-symmetric plane loading, the Poisson’s effect leads to…
In this work, the orientation and propagation of cracks in fretting fatigue problems is analyzed numerically using the finite element method (FEM) and the extended finite element method (X-FEM). The analysis is performed by means of a 2D…
The presence of notches and other stress concentrations in turbine blades and other notch hydraulic components is a current problem in engineering. It causes a reduction of endurance limit of material. In that sense, specimens of the ASTM…
In this paper, the fatigue crack growth simulation of two non-coplanar embedded cracks using the s-version finite element method is presented, and the validity and reliability of the alignment rule for two non-coplanar cracks are…
In this paper, the macro and micro-mechanical fracture behavior was studied for aluminum (Al6061) alloy matrix, reinforced with various proportions of TiC particles such as 3wt%, 5wt% and 7wt%. The Al6061-TiC metal matrix composites were…
A new fatigue testing device has been developed to test specimens under biaxial loading at 20 kHz. A flat smooth specimen with a disc geometry is placed on a torus frame and cyclically loaded at the center of its upper face. Disc bending…
This paper deals with the fatigue crack propagation behavior of rolled AZ31B magnesium alloy (grain size: approximately 40 ?m). Fatigue crack propagation tests were performed on single edge notched tension specimens at a stress ratio of R…
In the present work, the fracture performance of pre-cracked reinforced concrete beams was investigated numerically and experimentally. Experimental and numerical programs were designed to examine the effect of beam width, b, (120 and 250…
In this study a procedure to stress intensity factors calculation for imitation models made of titanium alloy is described. In service fatigue cracks are detected in a disk and blade “dovetail type” attachment. On the base of this…
Localized displacement measurements based on electronic speckle-pattern interferometry are used to obtain crack mouth opening displacement (CMOD), stress intensity factor (SIF) and T-stress values during crack growth around cold-expanded…
The publication presents a cruciform specimen for the determination of cyclic crack growth data under biaxial loading. The design of the specimen with slotted loading arms allows good decoupling between the two loading directions. For…
In this paper, numerical investigation was carried out to quantify the effect of the cold expansion on fatigue crack initiation in Aluminium alloy. The improvement in fatigue initiation life of specimen after the cold expansion process was…
With the development of the building industry, various novel building materials have emerged. Modern buildings requires higher on performance of building materials, and the performance of old buildings has not been able to keep up the pace…
The current work presents a novel methodology for the experimental quantification of the crack tip plastic zone during fatigue crack growth. This methodology is based on the application of yield criteria to estimate the area and the shape…
This paper contains a proposition setting out a new way of determining an orientation angle of the critical plane. The applied method involves an analysis of fatigue life results’ scatter of several selected materials on the basis of a new…
Fatigue crack growth (FCG) is associated with irreversible and non-linear processes happening at the crack tip. This explains different problems observed in the use of da/dN-?K curves, namely the inability to explain stress ratio and load…
The blade-disc dovetail interface in an aero-engine compressor is characterized by a non-uniform pressure distribution which can be obtained by an equivalent flat with round edge-on-plate configuration. The contact tractions for a mating…
Welded ‘T-junctions’ are tested at different load ratio for constant and variable amplitude loading. Fatigue results are analyzed through the type of fatigue mechanisms depending on the loading type. A gradient approach (WSG: Welded Stress…
The current work presents an experimental study on the use of the crack tip opening displacement (CTOD) to evaluate its ability to characterise fatigue crack growth. A methodology is developed to measure and to analyse the CTOD from…
Most techniques of measuring the stress intensity factor (SIF) in the cracking process assume a crack in a planar medium. Currently, there is no effective approach for curved brittle shells, particularly for non-developable cases, i.e.…
The paper studies the adhesive strength of aluminum alloy specimens bonded with the use of an epoxy adhesive, under the tensile-shear stress state, depending on the testing temperature. Tension of modified Arcan specimens with load angles…
