Tip: use quotes for an exact phrase, e.g. "teacher education"
An experimental campaign was developed to study fatigue crack growth in Haynes 230, a Ni-based superalloy. The effects of crack closure were investigated with digital image correlation, by applying two different approaches. Initially, full…
Fatigue cracking of longerons manufactured from Al-alloy AVT-1 for helicopter in-service rotorblades was considered and crack growth period and equivalent of tensile stress for different blade sections were estimated. Complicated case of…
Damage in RC structures causes the degradation of stiffness and frequency parameters. In this study, the relationship between the two coefficients and damage severities is numerically investigated considering a three-dimensional (3D)…
The paper is devoted to theoretical and experimental investigation of materials behavior on postcritical deformation stage (strain softening). Tests results, which confirm theoretical justification of specimen configuration impact on the…
The present paper is concerned with the formulation of an elasto-plastic strain based approach suitable for assessing fatigue strength of notched components subjected to in-service variable amplitude cyclic loading. The hypothesis is…
Selecting the correct objective function is the critical precondition for a successful optimization task. The validity of this condition is also required when optimization algorithms are needed for the inverse identification of the unknown…
Le problematiche relative all’utilizzo delle normative nell’ambito della progettazione a fatica di strutture in leghe di alluminio sono state di recente affrontate in numerosi lavori che hanno messo in luce sia le difficoltà legate al…
This paper presents results of experimental examinations of stress concentration influence to fatigue life of butt welded joints with K-groove, produced from the most frequently used structural steel S355J2+N. One group of experiments…
As often done in design practice, the Wöhler curve of a specimen, in the absence of more direct information, can be crudely retrieved by interpolating with a power-law curve between static strength at a given conventional low number of…
The article describes the results of laboratory studies on the unfrozen water content and ultimate long-term strength of frozen clay and chalk samples in the temperature range from −10 to −25 °C. The soil samples contained dissolved salt…
Laser shock peening (LSP) is used to enhance surface quality of the metallic structures by the generation of compressive residual stresses on it. This work studies the effect of the main LSP parameters on residual stress fields by the…
Fatigue cracking of longerons manufactured from Al-alloy AVT-1 for helicopter in-service rotor-blades was considered and crack growth period and equivalent of tensile stress for different blade sections were estimated. Complicated case of…
A new technique of Layered Hollow Core Slab (LHCS) has been used to obtain a slab with an optimum weight-to-strength ratio. Specimens with a 90 mm top layer of High Strength Concrete (HSC) and a 90 mm bottom layer of Lightweight Aggregate…
Overall structural integrity and load transfer between concrete and reinforcement enabling composite action relies on the bond between concrete and reinforcement. Bond strength determination of reinforced concrete is an essential task that…
Fatigue lifetime assessment is essential in the design of structures. Under-estimated predictions may result in unnecessary in service inspections. Conversely, over-estimated predictions may have serious consequences on the integrity of…
Obiettivo ultimo delle ricerche nelle quali si inquadra questo studio è superare, o almeno limitare, la necessità di complicate e costose prove sperimentali a favore di altri metodi predittivi della vita a fatica. Scopo specifico del…
The present study investigates the influence of corrosion exposure on the fatigue behavior of S460NL high-strength structural steel, a material that is frequently utilized in offshore and civil engineering structures. Accelerated corrosion…
This work is devoted to the application of the micromechanical Gurson-Tvergaard-Needleman (GTN) model to study the ductile tearing of 12NiCr6 steel. GTN model is widely used to describe the three stages of ductile tearing: nucleation…
The presence of a geometric discontinuity such as a crack or a notch can cause the failure of a structure during its use. Under various mechanical or thermal stresses, a high concentration of stresses can take place at the level of these…
Strain energy density is successfully used as criterion for failure assessment of brittle and quasi-brittle material behavior. This work investigates the possibility to use this method to predict the strength of V-notched specimens made of…
This research addresses environmental concerns by exploring environmentally friendly composite materials as substitutes for non-biodegradable synthetic fibers. The study proposes the development of polymer matrix composites reinforced with…
The work is devoted to experimental study of heat flow evolution at the fatigue crack tip during biaxial loading. The plane samples of titanium alloy Graid-2 with thick of 1 mm were weakened by notch to initiate fatigue crack at the center…
Different options that rely on fracture mechanics are currently used in engineering during the design and assessment of components. One of the most important aspects is the time taken for a crack to extend to its critical size. If this…
The development of additive technologies for manufacturing safety‑critical components operating under vibration must be accompanied by a careful analysis of the material’s resistance to high‑cycle fatigue (HCF). This paper presents a…
We predict the fatigue life of a planar tubular truss when geometrical parameters, material properties, and live loads are non-deterministic. A multi-level calculation uncertainty quantification framework code was designed to aggregate the…
In the article the deformation of different steels is analyzed using the autowave theory of plasticity. The article considers the possible use of an autowave model to formulate criteria for the structural strength of materials and…
Mounting stiffness has an important impact on a system’s structural dynamics and also on the durability of many structures. Mounts with tunable stiffness allow adapting a system’s structural dynamic behavior. Furthermore, they can be used…
This paper predicts the tension strength of Concrete-filled Branch Plate-to-Rectangular Hollow (CBPRH) joint by conducting experimental and theoretical analysis. A total of 46 X-joints with different geometric parameters were investigated…
Onyx ® is a new material composed of Polyamide 6 reinforced with short carbon fiber, used in the novel additive manufacturing composites technique. This paper aims to present the axial fatigue performance of this material with and without…
Deep drawing of sheet metal is a crucial industrial process due to its high productivity and low cost per unit produced. Stainless steels are ideal for this process, given their high deformability compared to other steels. Despite its…
The study of salt rocks deformation and fracture processes is an essential part of mining parameters justification for mineral salt deposits. The results of uniaxial compression tests on large salt rock specimens are presented as a loading…
Three-point bending fatigue test of 5083 and 5A06 aluminum alloy T-welded joints is carried out, and the fatigue life of the specimens with different influencing factors are obtained. Finite element model of the T-welded joint is…
Presently, Functionally Graded Materials (FGMs) are extensively utilised in several industrial sectors, and the modelling of their mechanical behaviour is consistently advancing. Most studies investigate the impact of layers on the…
The Algerian seismic code assumes that the beam-column joints in monolithic reinforced concrete (RC) buildings are fully rigid. However, many experiments have proven the existence of relative rotations in these connections, and then the…
An experimental protocol is described aiming to explore the influence of Type 2 Diabetes Mellitus on the biomechanical response of the bone tissue and, also, to quantify the potential beneficial role of a pharmaceutical treatment, based…
