Tip: use quotes for an exact phrase, e.g. "teacher education"
A Light Utility Helicopter (LUH), in the course of a training flight, leaving the ground during the taxi to take off, went into an uncontrolled rolling to the right; consequently the helicopter gradually laid down on the right side. The…
This paper examines the influence of controlled heat treatments on the mechanical behaviour of Ti-6Al-4V (Grade 5 Titanium alloy) to improve its performance in structural and high performance applications. Ti-6Al-4V is widely used in…
This work consists of an experimental study on the ageing response and resulting properties of AA7050 plate material. New heat treatments are investigated for achieving a peak-aged temper, as a T6 temper may be said to be, that achieves…
In the present study the impact behavior of gravity casting AlSi10Mg alloy was evaluated with an instrumented Charpy pendulum. The effect of hot isostatic pressing, also followed by a T6 treatment, was analyzed in comparison with samples…
Aluminium (Al) based composites enhance the mechanical and wear behavior by heat treatment. The quenching factors like cooling agent, cooling rate and temperature of cooling are expected to influence the hardness, tensile, and wear…
Starting from the research aimed at the development of substitute alloys for stainless steels, with the aim of replacing strategic metals such as chromium and nickel with the more available manganese, FeMnAlC alloys have been studied and…
The present paper describes a novel experimental technique recently presented that allows one to study interactions between the crack and microstructural barriers with an unprecedented level of ease and detail. The method consists in…
High Entropy Alloys (HEAs) is a unique class of materials that combine particular properties in a large-scale of temperatures, able to guarantee new unexplored materials and alloys with several potentially engineering applications (i.e.…
Additive manufacturing (AM) could be used to reduce the production times of prototypes; however, further research is required to address metals structural parts. To obtain the correct properties, some relevant factors to be considered are…
Additive Manufacturing (AM) is a new innovative technique that allows the direct fabrication of complex, individual, delicate and high-strength products, based on their 3D data. Selective Laser Melting (SLM) is one of the AM processes that…
Considerable efforts have been made over the last decades to improve performance of spring steels, which would increase the service time of springs and also allow vehicles weight reduction. There are different possibilities of improving…
The work is devoted to experimental investigation of the laser shock peening (LSP) effect on fatigue crack propagation rate and heat dissipation at the crack tip in specimens made of titanium alloy Grade 2 with a stress concentrator. It is…
An analytical model is developed to predict fatigue crack propagation rate under mode I loading in 2024 aluminum alloy with FSW HAZ material characteristics. Simulation of the HAZ local properties in parent 2024 AA was performed with…
Magnesium alloys have generated renewed interest as a light alloys; replacing some conventional structural materials for weight reduction in applications like aerospace, automotive and electronics industries. In interior components and…
The purpose of this study was to understand the behavior of martensitic H13 steel in accordance with the microstructural evolution, mechanical properties and wear in repeated tempering cycles. The microstructures were characterized by axio…
Hot rolling normalization technology for producing sheets from a low-carbon steel, Steel S355J2, used in the Bulgarian Metallurgical Plant “STOMANA Industry SA” is under investigation. A newly introduced automatic application optimization…
Delay fracture is an environmental embrittlement occurring when materials, environment and stress interact with each other and also a form of hydrogen induced material deterioration. It is a leading factor inhibiting the further…
The work is devoted to the experimental study of heat dissipation process caused by fatigue crack propagation. To investigate a spatial and time temperature evolution at the crack tip set of experiments was carried out using specimens with…
In the present paper, microstructural and mechanical properties of an innovative AlSi3Mg alloy were studied. Particularly, the effect of the addition of Cr and Mn on tensile strength and impact toughness was evaluated. In fact, the…
Al6061 and its composites are widely employed in applications requiring high strength and impact resistance. Heat treatment, particularly ageing, is a well-established method for enhancing the mechanical properties of these composites.…
The microstructure and mechanical properties of stainless-steel AISI 304 wire mesh–reinforced AlSi9Cu-matrix composite specimens obtained by gravity casting were investigated. Optical and scanning electron microscope analyses were carried…
Additive Manufacturing (AM) is a technological process in which elements are fruitfully built up adding materials layer by layer. AM had a massive development in recent times, thanks to its intrinsic advantages, especially if compared with…
Nowadays, an increasing number of oil and gas transmission pipes are constructed with high-strength low alloy steels (HSLA); however, many of these pipelines suffer from different types of hydrogen damages, such as hydrogen-induced…
The first stage of this study investigates the precipitation of free ferrite from the austenite on fully austenitized ductile iron. Several sets of samples of low alloy ductile iron are fully austenitized and then cooled down to different…
This study explores how ageing temperature and the volume percentage of Al2O3+B4C nanoparticles influence the machinability and hardness of stir-cast Al-7075 Metal Matrix Composite (MMC). Using liquid metallurgy techniques, hybrid…
To investigate the deterioration of granite under microwave irradiation and heat transfer, granite specimens were heated up to 400-1000 °C and then kept for 15 min. Uniaxial compressive strength testing results demonstrate a similar…
This article presents the bending fatigue behavior and the scatter-band analysis of aluminum alloys under beneficial conditions of nano-clay-particles and heat-treating, compared to detrimental conditions of the mechanical stress and the…
Experimental tests were conducted on additive manufactured Ti-6Al-4V titanium alloy to investigate the mechanical and crack properties under multiaxial cyclic loading. Selective Laser Sintering technique (SLS) was employed to fabricate…
A new class of material characterized by mechanical properties close to the traditional low and medium carbon steel is the Ductile Cast Irons (DCIs). High castability and low production costs allow them to be used in many fields, ranging…
In the present paper, the influence of eutectic and intermetallic phases on cavitation resistance of Al-Si alloys was studied. In fact, Al-Si alloys are commonly used for the production of components, such as cylinders, pistons, pumps…
The major drawback observed in the ceramic particles reinforced aluminium matrix composites (AMCs) is the reduction of ductility. Incorporating fine metallic particles along with the ceramic reinforcements in the aluminium matrix tends to…
The fatigue strength evaluation and fracture behavior for a dual phase steel-AA6061-T6 bonded joints with three different adhesives (DC-80, Betamate 120 and MP55420) are presented in this paper. Single lap shear tests were used to…
Protection against metallic materials corrosion is one of the most important means to reduce both aintenance costs and environmental impact. In the last years new studies on chemical baths compositions and fluxes have been performed in…
This paper presents a novel modification of the multilevel statistical model for describing the subgrain boundary migration that can explicitly account for the topology of subgrain structures in the form of Laguerre polyhedra. The…
Additive manufacturing research is continuously growing, and this field requires a full improvement of the capability and reliability of the processes involved. Of particular interest is the study of complex geometries production, such as…
The main aim of the research work is to examine the fracture toughness of the dual phase steels prepared using the intermediate quenching method. The ferrite-martensite dual phase (DP) steel is produced using low carbon micro alloyed steel…
