Tip: use quotes for an exact phrase, e.g. "teacher education"
In the present article, a review of the complete characterization in different aggressive media of a Ti-6Al-4V titanium alloy, performed by the Structural Mechanics Laboratory of the University of Bergamo, is presented. The light alloy has…
Multiaxial fatigue is a very important physical phenomenon to take into account in several mechanical components; its study is of utmost importance to avoid unexpected failure of equipment, vehicles or structures. Among several fatigue…
The peculiar geometrical shape and working conditions of crankshafts make fatigue becoming responsible for most of the failure cases in such components. Therefore, improvement of crankshaft performance requires enhancing its fatigue life.…
Nowadays most industrial realities undergo a strong push to improve cost-effectiveness, productivity and quality of manufactured products. In particular we focussed our attention in the area of design of plastic structural components…
This article presents the bending fatigue behavior and the scatter-band analysis of aluminum alloys under beneficial conditions of nano-clay-particles and heat-treating, compared to detrimental conditions of the mechanical stress and the…
High resolution synchrotron X-ray tomography has been used to obtain 3D images of arrested cracks initiated at small artificial defects located on the surface of cylindrical steel specimens subjected to mode I fatigue loading. These…
Tensile and stress controlled fatigue tests were performed to investigate the influence of forging at a temperature of 400°C at different rates, on the performance of extruded AZ31B magnesium alloy. The obtained microstructural analysis…
Fatigue surface crack growth and the in-plane and out-of-plane constraint effects are studied through experiments and computations for aluminium alloy D16T. Subjects for studies are cruciform specimens under different biaxial loading and…
Various input variables, including corrosion time, fretting force, stress, lubrication, heat-treating, and nano-particles, were evaluated by modeling of stress-controlled fatigue lifetimes in AlSi12CuNiMg aluminum alloy of the engine…
Abstract. In this article, the effect of nano-clay particles and heat-treating on thermo-mechanical fatigue (TMF) behaviors and failures of piston aluminum-silicon (AlSi) alloys was investigated. For this purpose, thermo-mechanical fatigue…
The objective of the present paper is to investigate the stress-controlled low-cycle fatigue behavior of piston aluminum-silicon (AlSi) alloy reinforced with nano-clay particles and T6 heat-treatment. The piston aluminum-silicon alloy…
Aeroengine manufacturers have to demonstrate that critical components such as turbine disks, made of DA Inconel 718, meet the certification requirements in term of fatigue crack growth. In order to be more representative of the in service…
Ductile cast irons (DCIs) are characterized by a wide range of mechanical properties, mainly depending on microstructural factors, as matrix microstructure (characterized by phases volume fraction, grains size and grain distribution)…
The quickly identify of fatigue limit of a mechanical component with good approximation is currently a significant practical problem not yet resolved in a satisfactory way. Generally, for a mechanical component, the fatigue strength…
Fatigue tests were conducted on cylindrical bars specimens to understand the fatigue behavior of SICLANIC®. Although it displays good resistance in monotonic tension, this material weakens and shows a softening in repeated solicitation.…
The three dimensional growth of fatigue cracks in samples of nodular graphite cast iron is characterized using laboratory X-ray computed tomography. The cracks grow from laser machined artificial defects, their development is monitored in…
The fatigue strength evaluation and fracture behavior for a dual phase steel-AA6061-T6 bonded joints with three different adhesives (DC-80, Betamate 120 and MP55420) are presented in this paper. Single lap shear tests were used to…
The main goal of the present research is to propose an integrated methodology to address the fatigue performance of topology optimized components, produced by additive manufacturing. The main steps of the component design will be…
Fatigue takes a place more and more important in the design of structures, it remains a key point in the mechanical dimensioning of structures. The Friction Stir Welding (FSW) process is regarded today as the most promising alternative to…
The present study is concerned with formulation of a model for the creep–fatigue crack growth rate prediction on the base of fracture damage zone concepts. It is supposed that crack growth rate can be determined by integration of damage…
Thanks to the progress of research on thermoplastic materials, the properties of composite materials have improved considerably. The aim of this study is the evaluation of fatigue strength of glass-fibre-reinforced polypropylene composite…
The mechanical fatigue behavior of gold microbeams is analyzed. Dedicated devices have been designed and built able to produce alternate loading on gold specimens; the electrostatic actuation is used as driving force. Gold beams are tested…
Experimental method for a characterization of high-cycle fatigue evolution of residual stress near cold-expanded hole is developed and implemented. The technique is based on simultaneous measurements of deformation response to narrow…
Shape memory alloy (SMA) wires are employed as actuators in small devices for consumer electronics, valves and automotive applications. Because of the continued miniaturization of all the industrial products, nowadays the tendency is to…
