Tip: use quotes for an exact phrase, e.g. "teacher education"
A recently introduced solution for the stress- and displacementfields, developed in a multi-layered circular ring, composed of a finite number of linearly elastic concentric layers, subjected to a parabolic distribution of radial stresses…
The very high cycle region of the S-N fatigue curve has been the subject of intensive research on the last years, with special focus on axial, bending, torsional and fretting fatigue tests. Very high cycle fatigue can be achieved using…
A recently proposed cohesive-zone model which effectively combines damage, friction and mechanical interlocking has been revisited and further validated by numerically simulating the pull-out test, from a concrete block, of a ribbed steel…
Orthotropic decks were applied to the long span bridges after World War II due to several advantages, such as light weight, high strength, few deck joints, durability, rapid construction, life-cycle economy. The fatigue problem of…
Carbon nano-tubes as a kind of novel nanometer material have been extensively applied in cement-based composite materials to improve their properties. This study prepared carbon nano-tubes cement based composite materials by evenly…
The present work summarizes a numerical procedure aimed at the evaluation of the residual strength of a cracked lap joint, based on the competing failure mechanisms regulated by the R-curve analysis and plastic collapse. The model adopted…
The paper provides an evaluation of the nonlinear dynamic response of a cantilever beam made of composite material subjected to low-velocity impacts. The structure is assumed to respond in a quasi-static manner and modelled by a continuous…
In this work, powder compaction process was investigated by using a numerical material model, which involves Mohr-Coulomb theory and an elliptical surface plasticity model. An effective algorithm was developed and implemented in the ANSYS…
Natural stones like marbles are often employed as façade panels to externally cover buildings. These natural materials tend to exhibit a quasi-brittle nonlinear fracture behaviour which, conversely to concrete counterpart, has much less…
Combining experimental and computational method for determination of the singular and the nonsingular stress terms along the front of the 3D surface crack is proposed. Evaluation of the terms is based on comprehensive comparison between…
In the present work we present some results of numerical experiments obtained with a variational model for quasi-static Griffith-type brittle fracture. Essentially the analysis is based on a recent formulation by Francfort and Marigo the…
The indentation response of a pseudoelastic nickel-titanium based shape memory alloy (SMA) has been analyzed. Indentation tests have been carried out at room temperature using a spherical diamond tip and indentation loads in the range…
This work primarily aims to carry out a numerical assessment of the seismic vulnerability of the historical Rammed Earth (RE) remains of the enclosure of Mansourah, a small town in the Wilaya (Province) of Tlemcen, in northwestern Algeria.…
The literature review showed insufficient relevant research on the application of Glass-Fiber-Reinforced-Polymers (GFRP) gratings in the structural elements, while GFRP bars, laminate, sheets, and strips, have been extensively explored.…
Infrastructure aging is an important problem nowadays, in particular for countries like Italy in which the main motorways were built 50 years ago. Huge budgets are necessary to keep infrastructure and bridges in service. In addition, the…
The aim of this work is the study of the effect of the finishing of the edge of glass when it has a structural function. Experimental investigations carried out for glass specimens are presented. Various series of annealed glass beam were…
The stability of any structure is possible if foundation is appropriately designed. The Bandar abbas is the largest and most important port of Iran, with high seismicity and occurring strong earthquakes in this territory, the soil…
Aluminum composites with varied weight percentages of 0-2.5 B4C particles and micro- and nanoparticle sizes were fabricated by stir-casting. The material's mechanical and wear characteristics were evaluated. We used dry pin-on-disc wear…
In this study, a novel quasi-three dimensional hyperbolic high-order shear deformation theory (quasi-3D HHSDT) is developed for free vibration analysis of porous functionally graded plates (FGPs). There are six unknowns in the current…
The objective of the study is to introduce an experimental uncertainty budget process for concrete compressive strength test, based on a protocol that incorporates effects of multiple factors significant for the measurement result.…
The behavior of thermoplastics depends on several factors, mainly time and temperature. The present work is the subject of an analysis of the dependence of viscoelastic viscoplastic parameters of a model of rheological behavior at the…
The present work aims at developing a new approach towards the analysis of the crack path through the access to the information from the infrared (IR) video imaging of the steady fatigue crack growth. We first test some commonly available…
Two experimental techniques are used study the response of cement mortar beams subjected to three-point bending under various loading protocols. The techniques used are the detection of weak electric current emissions known as Pressure…
Most mechanical components experience multi-axial cyclic loading conditions during service. Experimental analysis of fatigue cracks under such conditions is not easy and most works tend to focus more on the simpler but less realistic case…
According to the research conducted, the asymmetric multi-storey buildings are complex and suffer from severe damage caused by increased torsional response. This paper addresses the behavior assessment of setback building with irregularity…
ABSTRACT. The paper presents an analysis of an isotropic circular axisymmetric perforated plate loaded with concentrated force Pi applied in the geometric center of the plate using finite element software ANSYS. The test plate with…
The objective of the present paper is to investigate the stress-controlled low-cycle fatigue behavior of piston aluminum-silicon (AlSi) alloy reinforced with nano-clay particles and T6 heat-treatment. The piston aluminum-silicon alloy…
Departing from pioneering Heyman modern rational investigations on the purely-rotational collapse mode of least-thickness circular masonry arches, the hypothesis that joint friction shall be high enough to prevent inter-block sliding is…
Despite the extensive studies on the effect of width-thickness ratio and residual stress on member behavior, few scholars have probed into the residual stress distribution on the I-section members. Based on the principle of blind hole…
An analysis focused on capturing the phenomenon of quasibrittle fracture is presented. Selected parameters relevant for quasi-brittle fracture are evaluated and an assessment of their dependence on the size and shape of the test specimen…
The use of temporary hip prosthesis made of orthopedic cement (spacer) in conjunction with antibiotics became a prevalent method used for prosthetic infections remedy; consequently, this method makes bone cement (PMMA) more fragile. Hence…
Metaheuristic algorithms have known vast development in recent years. And their applicability in engineering projects is constantly growing; however, their deferent exploration and exploitation techniques cause the engineering problems to…
The current work presents an experimental study on the use of the crack tip opening displacement (CTOD) to evaluate its ability to characterise fatigue crack growth. A methodology is developed to measure and to analyse the CTOD from…
Elbows under load experience more stress and strain than straight tubes. The strength of the composite tubes plays an important role in their use, the damage under a thermomechanical behavior of a composite tubular structure bent between…
The possibility of obtaining band gap structures in chiral auxetic lattices is here considered and applied to the case of inertial locally resonant structures. These periodic materials are modelled as beam-lattices made up of a periodic…
The numerical modeling and wave theory are used in tsunami mitigation analysis. It is assumed sea forest is simulating offshore structure submitted to wave loads. The sea forest acts simulate break waves in conservation of coastal…
Arch bridges play an important role in rural roads in China. Due to insufficient funds and a lack of management techniques, many rural arch bridges are in a state of disrepair, unable to meet the increasing transportation needs. Thus, it…
In this paper an automatic procedure based on a machine learning approach is proposed to classify ductile cast iron specimens according to the American Society for Testing and Materials guidelines. The mechanical properties of a specimen…
In the last years, a large amount of fatigue test results from plain and bluntly notched specimens made of AISI 304L stainless steel were synthetized in a single scatter band by adopting the specific heat loss per cycle (Q) as a damage…
The evaluation of fracture mechanics parameters of materials has become very important part of considering the condition of older constructions as well as properties of newly developed materials. This contribution focuses on a numerical…
Ultra-high performance concrete (UHPC), a kind of composite material characterized by ultra high strength, high toughness and high durability. It has a wide application prospect in engineering practice. But there are some defects in…
A detailed investigation was conducted into the fracture mechanisms of cylindrical specimens made of a polycrystalline heat-resistant nickel-based alloy XH73MBTU-VD (EI698-VD), under uniaxial tension in the temperature range of 25–700°C.…
The Boussinesq solution, one of the fundamental problems in the theory of elasticity, enables an analysis of stresses and strains (displacements) in a semi-elastic space subject to surface loads. This solution has a form of formulas for…
Development of aluminium composites by stircasting technique is an effective method for fabrication of better quality of MMCs. Stircasting technique is one of the most commonly accepted techniques. In this research work, Al6061 / TiB2+CeO2…
Given the field of application and the many advantages, the use of FGM (Functionally Graded Materials) materials has recently been extended in several components and more particularly in cylindrical structures, which have been the subject…
In stress analysis of cracked plates, alongside the stress intensity factor which quantifies the singular stress component perpendicular to the crack plane, the role played in crack growth by the constant term parallel to the crack plane…
Manufacturing defects are inherent to any manufacturing process. However, in composite materials they might be unavoidable, e.g. ply waviness or even folds of plies are present in complex shaped parts during high pressure resin transfer…
In this work, the orientation and propagation of cracks in fretting fatigue problems is analyzed numerically using the finite element method (FEM) and the extended finite element method (X-FEM). The analysis is performed by means of a 2D…
Experimental indentations are carried out on items of two different materials, taken in several location of various components from high pressure gas turbine rotor which have seen an extensive service. The components object of…
In this research, the variational mode decomposition (VMD) method is used for the drive-by health monitoring of bridges. Firstly, the problem of a half-trailer tractor moving over a bridge is formulated. Next, a Finite Element (FE) code is…
