Tip: use quotes for an exact phrase, e.g. "teacher education"
Shape memory property characterizes the behavior of many Ti based and Cu based alloys (SMAs). In Cu-Zn-Al SMAs, the original shape recovering is due to a bcc phase that is stable at high temperature. After an appropriate cooling process…
Various input variables, including corrosion time, fretting force, stress, lubrication, heat-treating, and nano-particles, were evaluated by modeling of stress-controlled fatigue lifetimes in AlSi12CuNiMg aluminum alloy of the engine…
This study aims to investigate the delamination effect of a metal sandwich panel using a four-point bending simulation under continual spectrum loading. The most recent core designs of the sandwich panel have a cavity that can increase…
The paper analyses the fatigue tests of a specimen made of 16Mo3 steel and 6082-T6 aluminium alloy performed under bending and tensile conditions. It has been shown that in the case of bending of the 16Mo3 steel specimen, in low cycle…
The scaling of compression strength with porosity for aluminium foams was investigated. The Al 99.96, AlMg1Si0.6 and AlSi11Mg0.6 foams of various porosity, sample size with and without surface skin were tested in compression. It was…
The demanding material quality criteria in the automotive and aerospace industries have recently had an impact on the development of lightweight aluminium alloys. The choice and application of metal-matrix composites as structural…
Due to their severe operating conditions, many industrial components are subjected to complex combinations of cyclic mechanical stresses and thermal pressures. These combinations are responsible for the initiation and propagation of…
Numerical techniques have been widely applied in many recent works to investigate micro-scale behavior of materials. This work focuses on the analysis of strain localizations in a Nickel-based alloy, Haynes 230. Numerical models and…
This work is devoted to the development of an experimental method for studying the energy balance during cyclic deformation and fracture. The studies were conducted on 304 stainless steel AISE and titanium alloy OT4-0 samples. The…
Starting from the research aimed at the development of substitute alloys for stainless steels, with the aim of replacing strategic metals such as chromium and nickel with the more available manganese, FeMnAlC alloys have been studied and…
The fatigue strength evaluation and fracture behavior for a dual phase steel-AA6061-T6 bonded joints with three different adhesives (DC-80, Betamate 120 and MP55420) are presented in this paper. Single lap shear tests were used to…
This paper reports hardness testing conducted on welded butt joints by FSW and TIG welding process on similar and dissimilar aluminium alloys. FSW joints were produced for similar alloys of AA7075T651 and dissimilar alloys of AA7075T651…
This work consists of an experimental study on the ageing response and resulting properties of AA7050 plate material. New heat treatments are investigated for achieving a peak-aged temper, as a T6 temper may be said to be, that achieves…
Hybrid metal matrix composites (MMCs), recognized for their superior strength-to-weight ratios and synergistic property enhancements, are emerging as advanced materials capable of mitigating the inherent limitations observed in…
Residual stress significantly influences the mechanical performance, fatigue resistance, and structural reliability of titanium alloys used in engineering applications. This study investigates the residual stress distribution induced by…
Friction stir welding (FSW) is an extremely complex process because it depends on the intrinsic and extrinsic factors of the material under consideration. The purpose of the present work is to formulate a set of recommendations concerning…
Experimental tests were conducted on additive manufactured Ti-6Al-4V titanium alloy to investigate the mechanical and crack properties under multiaxial cyclic loading. Selective Laser Sintering technique (SLS) was employed to fabricate…
Machinability of engineering materials is crucial for industrial manufacturing processes since it affects all the essential aspects involved, e.g. workload, resources, surface integrity and part quality. Two basic machinability…
The influence of forging conditions on the propagation of physically small fatigue cracks has been studied for two high strength steels. Two surface conditions were produced after the forging process. The subsurface microstructure of the…
The present paper investigates the multiaxial fatigue strength of sharp V-notched components made of titanium grade 5 alloy (Ti-6Al-4V). Axisymmetric notched specimens have been tested under combined tension and torsion fatigue loadings…
In the past two decades, crack-tip mechanics has been increasingly studied with full-field techniques. Within these techniques, Digital Image Correlation (DIC) has been most widely used due to its many advantages, to extract important…
In this paper the fatigue crack growth tests were carried out on surface-crack tension (SCT) specimens, made of 7050 and Ti6Al4V alloys, with initial semi-elliptical surface cracks. Pure Mode I conditions were realized on SCT specimens…
Surface texturing plays a significant role on the tribological performance of contact surfaces. The tribological characteristics are mostly dependent upon the different pattern and methods of surface texturing. This research works…
Using a finite element calculation code, this work analyses the influence of friction during a stamping test conducted on the AA6060 aluminium-based alloy. The study focuses on phenomena happening when the sheet necking appears. This…
In this paper, the effect of corrosion on the performance of the bonded composite patch repair in aluminum alloy A5083 marine structure was investigated using three dimensional finite element methods. To this end, two patches made in…
Experimental indentations are carried out on items of two different materials, taken in several location of various components from high pressure gas turbine rotor which have seen an extensive service. The components object of…
Abstract. In this article, the effect of nano-clay particles and heat-treating on thermo-mechanical fatigue (TMF) behaviors and failures of piston aluminum-silicon (AlSi) alloys was investigated. For this purpose, thermo-mechanical fatigue…
Multiaxial fatigue is a challenging problem and, consequently, a number of methods has been developed to aid in design of components and assemblies. Following the complexity of the problem, these approaches are often elaborate and it is…
The work is devoted to experimental investigation of the laser shock peening (LSP) effect on fatigue crack propagation rate and heat dissipation at the crack tip in specimens made of titanium alloy Grade 2 with a stress concentrator. It is…
This study compares both uniaxial and multiaxial variable amplitude experimental crack growth data for naturally initiated fatigue cracks in tubular specimens of 2024-T3 aluminum alloy to predictions based on two state-of-the-art analysis…
The initiation and propagation of fatigue cracks during cyclic torsion loading was studied in a cast Al alloy (A357) with a relatively large (~500 ?m) grain size. 2D observations, revealed that multi site crack initiation occur on the…
Magnesium alloys have generated renewed interest as a light alloys; replacing some conventional structural materials for weight reduction in applications like aerospace, automotive and electronics industries. In interior components and…
The fatigue life prediction model of self-piecing riveting components of aluminum alloy is established and the effects of roughness and residual stress on fatigue life of self-piercing riveting components is analyzed by the model. Finite…
This paper presents a simple experimental procedure that greatly facilitates the use of digital image correlation (DIC) techniques in fatigue test conducted in resonant testing machines, without the need of test interruptions. This is…
The aim of this work is to investigate stress gradient effects on the fatigue life estimation of notched Al 7050-T7451 specimens under combined torsion and push-pull loading conditions. Initially, simple push-pull and torsion fatigue tests…
Additive manufacturing research is continuously growing, and this field requires a full improvement of the capability and reliability of the processes involved. Of particular interest is the study of complex geometries production, such as…
The publication presents a cruciform specimen for the determination of cyclic crack growth data under biaxial loading. The design of the specimen with slotted loading arms allows good decoupling between the two loading directions. For…
This article deals with identifying defects of layered high strength steel materials with the help of tomography measurement. Test samples were made of S960 High Strength Steel to which layers of either aluminium bronze, hardchrome, cobalt…
Fatigue surface crack growth and the in-plane and out-of-plane constraint effects are studied through experiments and computations for aluminium alloy D16T. Subjects for studies are cruciform specimens under different biaxial loading and…
In this paper, the hot tearing behaviour in Al-(4.8?6)%Cu sand mould castings was preliminary investigated by means of microstructural examination and image analysis. A dog-bone pattern was employed for the realisation of the castings and…
Three key qualities should define the structures used in the aviation industry: they should be light, rigid, and strong. These goals can be met by selecting lightweight, high-performance materials like titanium alloy or composites, but…
Laser shock peening (LSP) is used to enhance surface quality of the metallic structures by the generation of compressive residual stresses on it. This work studies the effect of the main LSP parameters on residual stress fields by the…
In the present paper, the multiaxial fatigue life assessment of notched structural components is performed by employing a strain-based multiaxial fatigue criterion. Such a criterion, depending on the critical plane concept, is extended by…
Additive Manufacturing (AM) is a new innovative technique that allows the direct fabrication of complex, individual, delicate and high-strength products, based on their 3D data. Selective Laser Melting (SLM) is one of the AM processes that…
New conception of adiabatic shear bands (ASB) and adiabatic shear failure mechanisms are proposed as special type of critical phenomen, structural-scaling transition, in the ensembles of microshears, governed by the characteristic…
The effects of SiC-Al2O3 particle in the Al alloy on the mechanical and wear characteristics of stir-casted Composites have been reported. The Al7075 is reinforced with 2, 4, 6 and 8 wt. % of (SiC + Al2O3) to manufacture the hybrid…
A new fatigue testing device has been developed to test specimens under biaxial loading at 20 kHz. A flat smooth specimen with a disc geometry is placed on a torus frame and cyclically loaded at the center of its upper face. Disc bending…
This paper discusses the effect of different surface treatments on shape memory alloy wires embedded in PolyEster (PE) and VinylEster (VE) polymeric matrices. In particular, two types of chemical etching and a chemical bonding with a…
Fatigue tests were conducted on cylindrical bars specimens to understand the fatigue behavior of SICLANIC®. Although it displays good resistance in monotonic tension, this material weakens and shows a softening in repeated solicitation.…
Brazing is a widely employed joining technique for aluminium components due to its cost-effectiveness and compatibility with complex geometries. However, the structural integrity of brazed joints under cyclic loading remains a scarcely…
