Tip: use quotes for an exact phrase, e.g. "teacher education"
The fatigue behaviour of concrete has become more important for the design of constructions due to the desire to build slimmer structures, which are more sensitive to fatigue loading. This article aims to evaluate and compare the fatigue…
The usage of rebars in construction is the most common method for reinforcing plain concrete and thus bridging the tensile stresses along the concrete crack surfaces. Usually design codes for modelling the bond behaviour of rebars and…
This paper investigated the static and dynamic behaviors of isotropic cracked simply supported beam using finite element analysis (FEA), ANSYS software. Modal and harmonic vibration analysis of intact and damaged beam were performed in…
This paper aims to analyze the multi-effects of the glass fiber reinforced polymer (GFRP) composite patch to repair the inclined cracked 2420-T3 aluminum plate. Three-dimensional finite element method (FEM) was used to study the effect of…
The present paper is concerned with the formulation of an elasto-plastic strain based approach suitable for assessing fatigue strength of notched components subjected to in-service variable amplitude cyclic loading. The hypothesis is…
Elbows under load experience more stress and strain than straight tubes. The strength of the composite tubes plays an important role in their use, the damage under a thermomechanical behavior of a composite tubular structure bent between…
This paper investigates numerically the behavior of Reinforced Concrete (RC) beams, strengthened using Carbon Fiber Reinforced Polymers (CFRP) sheets, subjected to impact loading. Three-dimensional finite element analysis was performed and…
In this work the finite element method (FEM) was used to analyze the mechanical behavior of the composite materials subjected to the mechanical loading. This behavior is studied in terms of stress intensity factor variation as a function…
The aim of this study is to deal with the simulation of intralaminar fatigue damage in unidirectional composite under multi-axial and variable amplitude loadings. The variable amplitude and multi-axial loading is accounted for by using the…
The existence of three-dimensional effects at cracks has been known for many years, but understanding has been limited, and for some situations still is. Understanding improved when the existence of corner point singularities and their…
In this study, the main objective was the creation of a code, which gives the capability to a Finite Element Analysis Program with no built-in crack study tools, to study the propagation of a crack, in a cracked surface. For this purpose…
Presented study is focused on the analysis of the dependence of the specific fracture energy value on the assumed work of fracture in threepoint bending tests. Specimens of different sizes and relative notch lengths are assumed in this…
This work is dedicated to the development of a fracture model for an elastic-brittle solid with statistically distributed strength characteristics of subregions and the application of this model to describe fracture processes of bodies…
10.3221/IGF-ESIS.74.05
Over the last two decades, piezoelectric actuators have emerged as a promising solution for structural repair. In this work, initially the stress intensity factor (SIF) estimation using the finite element (FE) approach at crack tips in…
A two-dimensional finite element analysis has been performed to investigate hydromechanical and conventional deep drawing processes. The effects of the fluid structure interaction on the material formability, the strain and the thickness…
This article deals with an analysis of the behaviour of brick ceramic walls. The behaviour of the walls was analysed experimentally in order to obtain their bearing capacity under static loading and their seismic resistance.…
Adding fibres to concrete provides several advantages, especially in terms of controlling the crack opening width and propagation after the cracking onset. However, distribution and orientation of the fibres toward the active crack plane…
Glass Fiber Reinforced Polymer (GFRP) is a promising alternative to steel due to its high strength, lightweight properties, corrosion resistance, and low maintenance requirements. This study examines the effect of internal GFRP I-sections…
A computational formulation able to simulate crack initiation and growth in layered structural systems is proposed. In order to identify the position of the onset interfacial defects and their dynamic debonding mechanisms, a moving mesh…
In this work, powder compaction process was investigated by using a numerical material model, which involves Mohr-Coulomb theory and an elliptical surface plasticity model. An effective algorithm was developed and implemented in the ANSYS…
This study investigates the effects of low concentration (0.1-0.4 wt.%) nano-boron carbide (B4C) reinforcement on the mechanical, thermal and fracture properties of epoxy nanocomposites. The nanocomposites were prepared via solution…
This paper discusses the application of machine learning techniques, notably artificial neural networks (ANN), in the fracture analysis of semi-infinite elastic plates with edge cracks. The Stress Intensity Factor (SIF) model for a…
With the development of the building industry, various novel building materials have emerged. Modern buildings requires higher on performance of building materials, and the performance of old buildings has not been able to keep up the pace…
The paper describes test specimen thickness effect on stress intensity factor (KI), and T-stresses stresses (T11 and T33) for a Compact Tension specimen. Formulations to estimate 3D KI, T11 and T33 stresses are proposed based on extensive…
In the Strain Energy Density (SED) approach for fatigue strength assessments of welded joints a well-defined control volume is considered. This volume surrounds the weld root or weld toe, both modelled like sharp (zero radius) V-notches…
This paper presents an advanced optimization methodology for truss structures, addressing both elasto-plastic design cases—where plastic deformations are controlled within predefined limits—and purely elastic scenarios, in which inelastic…
The research addresses evaluation of stress-strain state (SSS) in the “zygomatic bones–implants–denture base” system by varying the type and number of the zygomatic implants, as well as applying loads. The load magnitude was varied over a…
The evaluation of the seismic vulnerability of existing buildings is becoming very significant nowadays, especially for ancient masonry structures, that represent the cultural and historical heritage of our countries. In this research, the…
Fatigue crack growth (FCG) is associated with irreversible and non-linear processes happening at the crack tip. This explains different problems observed in the use of da/dN-?K curves, namely the inability to explain stress ratio and load…
The initiation and propagation of fatigue cracks during cyclic torsion loading was studied in a cast Al alloy (A357) with a relatively large (~500 ?m) grain size. 2D observations, revealed that multi site crack initiation occur on the…
The stepped isostress method (SSM) is an advanced technique which allows the prediction of the long-term behavior and enables the construction of creep master curves of materials with short-term experimental tests. However, the performance…
The paper describes a customer project, the objective of which was to develop a software program for the calculation of reinforced concrete and steel/concrete composite columns subjected to various loadings and exposed to normal…
Fatigue surface crack growth and the in-plane and out-of-plane constraint effects are studied through experiments and computations for aluminium alloy D16T. Subjects for studies are cruciform specimens under different biaxial loading and…
The direct identification of the cohesive law in pure mode I of Pinus pinaster is addressed. The approach couples the double cantilever beam (DCB) test with digital image correlation (DIC). Wooden beam specimens loaded in the…
Fracture behavior of adhesive joints is an important topic in structural design of new structural elements or in retrofitting of existing ones. The mechanical models available in literature capable of predicting the failure mode of these…
In this study, the finite element method is applied to investigate the mechanical behavior of aluminium notched structures reinforced by composite patch. In order to evaluate the efficiency of patches in the case of lateral semicircular…
The realization of a connection between a ceramic and a metal is always accompanied by the creation of a multi-axial stress field. Different physical and mechanical origins explain the genesis of stresses at the bonding interface in the…
In this paper, gradual demand for curved, stiffened panels composite emerged from carbon fiber reinforced plastics (CFRP); these are structures that are frequently used in aerospace engineering. Up to 50% of the primary structure of the…
The linear elastic analysis of homogeneous, isotropic cracked bodies is a Twentieth Century development. It was recognised that the crack tip stress field is a singularity, but it was not until the introduction of the essentially two…
During the last years many researchers put so much effort to design layered structures combining different materials in order to improve low fracture toughness and mechanical reliability of the ceramics. It has been proven, that an…
Stepped steel girders and beams with a jump in section depth are highly susceptible to local web buckling at the step location. Although tapered steel girders have been studied extensively by researchers, abruptly stepped steel girders…
Presence of cracks in mechanical components needs much attention, where the stress field is affected by cracks and the propagation of cracks may be occurred causing the damage. The objective of this paper is to present an investigation of…
The mechanical clinching process can be used for the load-bearing structures of thin-walled steel frame halls. Numerical simulation of crack propagation in a clinching joint using finite element method (FEM) software is an important tool…
Numerical simulation by plastic deformation of the shaping processes currently has a large industrial interest. It allows you to shorten the time of design and construction related products and tools to analyze and to optimize processes.…
Layered ceramic materials (also referred to as “ceramic laminates”) are becoming one of the most promising areas of materials technology aiming to improve the brittle behavior of bulk ceramics. The utilization of tailored compressive…
The concept of ratchetting strain as a crack driving force in controlling crack growth has previously been explored at Portsmouth using numerical approaches for nickel-based superalloys. In this paper, we report the first experimental…
This study investigates the free vibration behavior of 3D-printed PA6 layered plates by considering the effects of stacking sequence, infill ratio, and boundary conditions. Unlike previous works, this research provides a comprehensive…
This paper is devoted to the numerical and experimental study of ductile fracture in bulk metal forming of the 2017A-T4 aluminum alloy. From an experimental standpoint, the ductile fracture of the 2017A-T4 aluminum alloy is investigated…
This study has used the strain energy density (SED) approach to evaluate the stress intensity factor (SIF) of cracked cruciform welded joints in Hardox 450 steel. A microstructural analysis was made of Hardox 450 steel which is composed of…
The material with anisotropic properties are becoming widely essential due to the ease to manipulate their mechanical properties in order to obtain a particular quality, insure safety or a specific behavior. Those kind of materials are…
