Tip: use quotes for an exact phrase, e.g. "teacher education"
The aim of the paper was investigation crack initiation and fracture features developed during compression of Fe-based bulk metallic glass (BMG). These Fe-based BMG has received great attention as a new class of structural material due to…
Considerations are made for the fracture morphology and its evolution in relation to the brittle fracture along butt-weld, where crack path stability may play important roles in various aspects. Analyses of a kinked and curved crack are…
A Light Utility Helicopter (LUH), in the course of a training flight, leaving the ground during the taxi to take off, went into an uncontrolled rolling to the right; consequently the helicopter gradually laid down on the right side. The…
Plastics belong to the most complex and probably least understood engineering materials of today. Combining the best aspects of design, mechanical properties and manufacturing, the structural integrity of plastics is on par with aluminium…
Fatigue (high- and gigacycle) crack initiation and its propagation in titanium alloys with coarse and fine grain structure are studied by fractography analysis of fracture surface. Fractured specimens were analyzed by interferometer…
The modified disk shaped compact tension test is a configuration derived from standard compact tension test that is used for measuring fracture mechanical properties of primarily metallic materials. The compact tension configuration is…
The article conducts a study on the iron tailings sand concrete's fracture behaviour based on the double-K criterion. Five sets of standard three-point bending beam specimens of concrete with 0%, 25%, 50%, 75% and 100% iron tailings sand…
The microstructural origins of premature fatigue failures were investigated on a variety of forged components manufactured from AZ80 and ZK60 magnesium, both at the test specimen level and the full-scale component level. Both stress and…
Hexagonal boron nitride (hBN) and molybdenum disulfide (MoS2) fillers of 2 to 8 wt.% influence on toughness, microhardness and thermal stability of carbon fabric-reinforced epoxy composite (CFREC) reported. Mode-I, mixed-mode I/II…
Multi-cluster staged fracturing technology is an effective measure to stimulate the reservoir properties. However, the inter-cluster interference effect is obvious when the cluster spacing is very narrow, which seriously affects the effect…
The core of the present work concerns the analysis of the failure mode and the fracture process induced by the flexural load in Fibre Metal Laminates (FMLs). The influence of the connection layer placed between the composite ones and the…
The major drawback observed in the ceramic particles reinforced aluminium matrix composites (AMCs) is the reduction of ductility. Incorporating fine metallic particles along with the ceramic reinforcements in the aluminium matrix tends to…
In the current work 17-4PH Stainless Steel is deposited using SLM process. It is widely used to build structural parts appropriate for automotive, medical, and aerospace applications. The 17-4 PH SS samples were deposited using technical…
The aim of this study is to investigate whether exercise can reverse some of the adverse effects of high-fat-diet-induced obesity on lipid metabolism and bone biomechanical properties. A total of 26 adult male C57bl/6J mice were randomly…
Crack initiation characteristics and fatigue property of a high-strength steel in very-high-cycle fatigue (VHCF) regime under different stress ratios were investigated in this paper. Fatigue tests were performed at stress ratios of -1…
Focusing on ferritic-pearlitic DCIs, these alloys are characterized by a microstructure that ranges from a fully ferritic to a completely pearlitic matrix, and they are widely used for many applications (e.g. wheels, gears, crankshafts in…
In the current studies an investigations were made to know the effect of 63 micron sized B4C particles addition on the mechanical and wear behavior of aerospace alloy Al2618 metal composites. Al2618 alloy with different weight percentages…
In the present paper, microstructural and mechanical properties of an innovative AlSi3Mg alloy were studied. Particularly, the effect of the addition of Cr and Mn on tensile strength and impact toughness was evaluated. In fact, the…
New developments in thermal spraying processes may offer higher-quality alternatives to hard chrome plating and possibilities for hard chrome plating in a range of coating applications. These include spraying with high-velocity air fuel…
Most techniques of measuring the stress intensity factor (SIF) in the cracking process assume a crack in a planar medium. Currently, there is no effective approach for curved brittle shells, particularly for non-developable cases, i.e.…
The role of structural mechanisms responsible for the consequent staging of damage-failure transition as the combination and continuity of ductile and creep kinetics of the structure evolution and the modeling in dwell fatigue regime.…
Crack formation in hemispherical domes is a distinguished problem in structural mechanics. The safety of cracked domes has a long track record; the evolution of the cracking pattern received less attention. Here, we report…
